轴向位移的英文

• axial di lacement
• axial displacement

• "轴向"英文翻译    axial
• "位移"英文翻译    displacement; shift; drift; ...
• "轴向位移，保护" 英文翻译 :    axis disprotection
• "侧斜轴向位移" 英文翻译 :    skew-induced rake
• "齿轮轴向位移" 英文翻译 :    gear axial di lacement; gear axial displacement
• "接头轴向位移" 英文翻译 :    joint axial deformation
• "小轮轴向位移" 英文翻译 :    pinion axial di lacement; pinion axial displacement
• "轴向位移压缸" 英文翻译 :    axial displacement cylinder
• "轴向位移保护设施" 英文翻译 :    axial displacement protective device
• "轴向位移保护装置" 英文翻译 :    axial displacement limiting device; axial displacement protective device
• "轴向位移传感器" 英文翻译 :    axial displacement sensor
• "轴向位移型膨胀节" 英文翻译 :    axial movement type expansion joint
• "轴向位移指示器" 英文翻译 :    axial position indicator; shaft position indicator
• "超速和轴向位移脱扣" 英文翻译 :    over eed and axial di lacement trip; overspeed and axial displacement trip
• "光纤轴向位移传感器" 英文翻译 :    fibre axial displacement sensor
• "基准平面的轴向位移偏差" 英文翻译 :    deviation of datum axial drift
• "允许轴向位移的联轴节" 英文翻译 :    plunging joint
• "振动及轴向位移测控" 英文翻译 :    vibration and axial displacement probe
• "轴向位置" 英文翻译 :    axial position
• "侧向位移" 英文翻译 :    lateral displacement; lateral movement; lateral shift; side movement
• "垂向位移" 英文翻译 :    vertical deviation
• "法向位移" 英文翻译 :    heave; normal displacement
• "横向位移" 英文翻译 :    crosswind displacement; lateral displacement; lateral drift; lateral shift; pressure pattern displacement; transversal displacement; transversal shift; transverse displacement; transverse distribution
• "径向位移" 英文翻译 :    radial displacement
• "逆向位移" 英文翻译 :    upstream shift

• Axial displacement protective device
  轴向位移保护设施
• Gear axial displacement
  齿轮轴向位移
• Based on the acquaintance of the reason and background of turbine ’ s differential expansion , the thermal characteristics and axial displacement of the steam turbine rotor have been discussed
  本文在介绍和了解汽轮机胀差产生现象的前提下,着手了解研究汽轮机转子的热力学特点和轴向位移。
• The paper researches a kind of system measuring the temperature and displacement of the optical fiber that can monitor and control simultaneously the temperature and displacement of the blades two - way signals of the turbine , and alert when the emergencies happen
  本课题研究的光纤温度位移测量系统能在恶劣的环境下，同时实时监测涡轮机轴温及其轴向位移两路信号，保证其正常工作，并在发生异常情况时，能立刻报警。
• When the fill factor is less than 1 , the concentrated tensile stress appeares near edge of disk surface , while the fill factor reaches up to 1 , the surface exhibites compressive stress , and the center is less tensile stress
  当抽运光斑未充满激光介质时，介质的表面靠近边缘处会出现大的拉应力集中，并且介质表面的最大轴向位移和最大拉应力随光斑填充因子增大而增大；而当抽运光充满介质时，表面是压应力，较小的拉应力存在于介质内部。
• 3 . as for side web girder , the principle of minimum potential energy has been introduced . by assuming different displacement function , the force and stress formulae for flanges under uniform loading , horizontal axial force , or vertical concentrated force have been derived
  对于边主肋截面主梁，本文介绍了能量变分法，通过假定板不同的轴向位移函数，推导了悬臂梁在均布荷载、水平轴向力、竖直集中力作用下的微分方程和应力计算公式。
• Comparing experimental results with the numerical analytic results using the criterion , it is found that the criterion employs the axial deformations of bracing members as fatigue damage parameters and can be applied to real - time estimation of low - cycle fatigue damage of bracing members under a loading history - dependent random stale
  研究结果表明：本文方法以钢支撑轴向位移为损伤参量，能实时估算在随机位移荷载下钢支撑的低周疲劳累积损伤发展，并与试验结果吻合较好。
• When the pumping area cannot approach the disk had aperture , the concentrated tensile stress appears near the edge of disk hard aperture , while the disk is pumped full aperture the surface exhibits compressive stress , and center is tensile stress which is lesser
  当抽运光斑未充满激光介质时，介质的表面靠近边缘处会出现大的拉应力集中，并且介质中最大拉应力和表面的最大轴向位移随抽运光斑尺寸缩小面增大；而当抽运光充满介质时，表面是压应力，较小的拉应力存在于介质内部。
• When the dimension of the pump is not particular , you can make a model by reverse engineering . iii ) there is a small flat metal piece on the outside of the torque converter ' s shell , called tab . system can get the axial rigid displacement of the equipment by measuring this tab ' s axial movement
  通过本课题研究得到以下结论：一、液力变矩器在加速状态产生弹性变形引起颈端和柄端的轴向位移和在加压状态时产生的弹性变形引起柄端的轴向位移均朝向发动机一侧；而在加压状态时产生的弹性变形引起颈端的轴向位移方向相反。
• By it , the temperature and axial displacement on axes around the blades of the turbine can be measured . the advanced circuits monitor their change . if the temperature and displacement go beyond the normal range , the alert will be sent out , and they can be stopped and repaired " at that time
  涡轮机的工作环境恶劣，为克服环境给测量带来的困难，采用非接触式测量方法对涡轮机轴的温度和涡轮机轴的轴向位移进行测量，采用精确的电路监控温度和位移的变化，若温度和位移超出其正常工作范围，立刻发出警报，停止其工作以进行及时的修理。