耐热温度的英文

• heat-resistance temperature

• "耐热"英文翻译    heat-resisting; heatproof; r ...
• "温度"英文翻译    temperature
• "油漆及涂料等的耐热温度" 英文翻译 :    paint resist temperature; paintresisttemperature
• "热温度" 英文翻译 :    bolometric temperature
• "暗红热温度" 英文翻译 :    dark red heat; low red heat
• "白热温度" 英文翻译 :    brightness temperature
• "赤热温度" 英文翻译 :    red heat temperature
• "地热温度" 英文翻译 :    geotemperature; geothermal temperature
• "地热温度；地温" 英文翻译 :    geotemperature
• "电热温度计" 英文翻译 :    thermelometer
• "废热温度" 英文翻译 :    heat-rejection temperature
• "过热温度" 英文翻译 :    overtemperature; super heating temperature; superheat temperature; superheating temperature; superheattemperature
• "红热温度" 英文翻译 :    red heat temperature
• "后热温度" 英文翻译 :    postheating temperature
• "加热温度" 英文翻译 :    heating temperature; heating-up temperature
• "绝热温度" 英文翻译 :    adiabatic temperature
• "均热温度" 英文翻译 :    soaking temperature
• "预热温度" 英文翻译 :    preheat temperature; preheating temperature; preheattemperature
• "自热温度" 英文翻译 :    self-heating temperature
• "地热温度测量" 英文翻译 :    geothermometry
• "二次加热温度" 英文翻译 :    reheat temperature
• "高热温度状况" 英文翻译 :    hyperthermic temperature regime
• "过热温度调节" 英文翻译 :    superheat control
• "过热温度界限" 英文翻译 :    hyperpyrexial temperature limit
• "火焰绝热温度" 英文翻译 :    adiabatic flame

• Ebonite - determination of martin heat resistance temperature
  硬质橡胶马丁耐热温度的测定
• Their properties have been investigated by using scanning electronic microscopy ( sem ) , differential scanning calorimetry ( dsc ) , x - ray diffraction ( xrd ) , thermogravimetry - differential thermal analysis ( tg - dta ) , infrared spectroscopic analysis ( ir ) , and gas chromatography ( gc ) , etc . the effects of the mulser ' s stirring rate and the emulsifier concentration on the properties of encapsulated pcms have been systematically studied , and nanopcms have been obtained by increasing the stirring rate or the emulsifier concentration . the influences of different nucleating agents on micropcm performances have also been investigated in detail to search for a suitable nucleating agent to prevent micropcms from super - cooling
  首先，系统研究了乳化机转速和乳化剂浓度对胶囊性能的影响，并通过提高转速或乳化剂浓度获得相变材料纳胶囊；其次，系统研究了不同成核剂对微胶囊性能的影响，找到合适的成核剂抑制了相变材料微胶囊的过冷现象；再次，详细研究了环己烷对胶囊性能的影响，并通过添加适量环己烷提高了相变材料微胶囊及纳胶囊的耐热温度。
• Based on the characteristics of silicon whisker , the research on the modification of pa6 by silicon whisker sio2 - jx was made , and the result showed that the tensile strength , impact strength , brinell hardness , and heat resistance increased with the increase of the content of the whisker ; sio2 - jx could replace short glass fiber in the modification of pa6 , improving the heat distortion temperature , removing the appearance of glass fiber , reducing shrinkage and the cost
  摘要利用晶须矽纤维状的特性，对其填充于龙玻纤改性进行研究，结果表明，随晶须用量的增加，材料的拉伸强度、冲击强度，布氏硬度、耐热温度均得到提高；晶须矽可取代短玻纤使用，提高热变形温度、消除玻纤外露，降低收缩率及生产成本等。