着靶的英文

• landing

• "着"英文翻译    wear; dress
• "靶"英文翻译    target
• "束着靶" 英文翻译 :    beam landing
• "着靶不良" 英文翻译 :    poor landing
• "电子束着靶点" 英文翻译 :    beam impact point
• "对着靶子射击" 英文翻译 :    fire at the target
• "射束着靶误差" 英文翻译 :    beam impact errors
• "电子束着靶误差" 英文翻译 :    beam impact errors; beam landing errors
• "着暗褐色的" 英文翻译 :    dun coloured
• "着比粒" 英文翻译 :    kinetochore
• "着" 英文翻译 :    着助词1.(表示动作的持续) 风轻轻地吹着。 the wind is blowing gently. 他提着箱子走了进去。 he went in carrying his suitcase. 他正吃着午饭呢。 he is having his lunch. 一大片金黄的稻子等着收割。 a vast golden stretch of rice was waiting to be cut.2.(表示状态的持续) 窗子开着。 the window is open. 桌子上放着一台收音机。 there is a radio on the table.; a radio stands on the table. 山上覆盖着厚厚的积雪。 the mountains are covered with thick snow.3.(用在动词或表示程度的形容词后面, 加强命令或嘱咐的语气) 脚步轻着点儿。 walk more quietly. 你听着。 you just listen. 快着点儿。 be quick.4.(加在某些动词后面, 使变成介词) 为着 for; 顺着 along; 照着 according to; by; in
• "着笔" 英文翻译 :    put pen to paper; begin to write or paint 如何着笔? how to begin the writing [painting]
• "啄癖" 英文翻译 :    cannibalism
• "着痹" 英文翻译 :    fixed arthralgia
• "啄肱肌囊" 英文翻译 :    bursa of coracobrachialis muscle
• "着边" 英文翻译 :    margination
• "啄肱肌" 英文翻译 :    coracobrachialis muscle

• Measurement system for precise bullet location and signal processing circuitry
  弹丸着靶坐标测试系统的原理与信号处理电路
• Beam landing errors
  电子束着靶误差
• Beam impact errors
  电子束着靶误差
• In this paper , firstly the macro parameter of the series connection app was comprehensively analyzed , among which the trajectory location of the bullet emission and the terminal velocity of the bullet were mainly analyzed , and the feasibility of the series connection app to cope with explosive reactive armor was demonstrated . and then the macro design about the head of the series connection app was made , among which a particular analyse about the bullet " s launching process was made , from which we concluded the relation between the thickness of the airproof loop and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the burning rate of the powder and the relation between the length of the bullet and the maximum pressure of the emission hole and the relation between the length of the bullet and the emitting time of the bullet , and the reasonable str ucture of the head of the carrier and bullet were designed , then the intensity of the head of the carrier was checked out using of the software of ansys
  本文首先对子母式穿甲弹总体参量作了全面的计算分析，其中主要分析了子弹射出的弹道位置和必要的子弹着靶速度，论证了子母式穿甲弹对付爆炸式反应装甲的可行性，然后对子母式穿甲弹弹头部进行了总体设计，其中主要对子弹的发射过程进行了详细的分析，得出了母弹弹头部发射孔内闭锁环厚度与子弹飞离母弹速度的关系、子弹长度与子弹飞离母弹速度的关系、子弹长度与火药燃烧率的关系、子弹长度与母弹弹头部发射孔内最大压力的关系以及子弹的长度与子弹发射所需时间的关系，设计出了合理的母弹弹头部结构和子弹的结构，并利用ansys有限元分析软件对母弹弹头部的强度进行了校核。