浇道的英文

• feeder
• geat
• pouring channel
• pouring gate
• runner gate
• running channel
• sprue cold material trap

• "浇"英文翻译    pour liquid on; sprinkle wat ...
• "道"英文翻译    road; way; route; path
• "下浇道, 竖浇道" 英文翻译 :    down gate
• "下浇道，坚浇道" 英文翻译 :    down gate; down sprue
• "边浇道" 英文翻译 :    side gate
• "横浇道" 英文翻译 :    cross gate; runner
• "坚浇道" 英文翻译 :    down sprue
• "浇道棒" 英文翻译 :    runner stick
• "浇道比" 英文翻译 :    runner ratio
• "浇道砖" 英文翻译 :    runner brick
• "开浇道" 英文翻译 :    spruing
• "内浇道" 英文翻译 :    ingate
• "热浇道" 英文翻译 :    insulated runner hot runner
• "竖浇道" 英文翻译 :    down gate; down sprue; sprue
• "外浇道" 英文翻译 :    sprue
• "无浇道" 英文翻译 :    runner less; runnerless
• "下浇道" 英文翻译 :    down sprue
• "直浇道" 英文翻译 :    downsprue; sprue
• "不磨浇道" 英文翻译 :    no grind gate; no-grind gate
• "迭边浇道" 英文翻译 :    connor runner bar
• "叠边浇道" 英文翻译 :    connor runner bar
• "虹吸浇道" 英文翻译 :    siphon runner
• "浇道、进胶口" 英文翻译 :    sprue
• "浇道废料" 英文翻译 :    runner scrap
• "浇道浇口" 英文翻译 :    sprue gating

• Tools for moulding - sprue bushes - dimensions iso 10072 : 2004
  模铸工具.浇道套.尺寸
• Study of u shaped girder with pre - cast main beam and cast in - situ slab
  预制主梁现浇道床板的槽形梁研究
• Sprue bushes for moulds
  铸模用浇道衬套
• Runner stripper plate
  浇道脱料板
• There are many causes , such as fast mold opening , high mold temperature , uneven mold temperature and imbalance of runners
  成品变形之原因相当多，如出模太快模温过高模温不均及浇道系统不对称等。
• The cross - section area of the internal sprue , the fill speed , the fill time and injection pressure are important die casting technology parameters
  摘要内浇道截面积、充填速度、充填时间和压射比压都是重要的压铸工艺参数。
• The max . temperature , cold runner result shows the max . temperature across the cold runner temperature profile calculated at the end of cooling time
  冷却结束时，冷浇道断面上最高温度分布情况（与顶出温度相比，判断此时是否顶出） 。
• Feeding , ingate design , air discharge , position of signal wire were analysed and discussed , aiming at the several questions in production of low pressure casting
  摘要根据低压铸造工艺的特点和生产实践，从补缩、内浇道设计、排气、信号线安放位置等方面进行了分析和探讨。
• Based on the new equilibrium solidification theory , the dispersed gate with flat 、 thin and wide rise neck , coupled with cold iron and warming riser , was adopted in the new gating system
  经分析主要原因是原工艺热冒口的冒口颈（内浇道）偏小，且开设的位置不合理，造成内浇道根部存在疏松和晶粒粗大铸造缺陷。
• The cross section area of the internal sprue of the die casting dies designed should be of proper value , and matches perfectly the fill speed , the fill time and injection pressure in case that the die casting dies fail in the design
  设计压铸模时应当确定恰当的内浇道截面积，并使之与充填速度、充填时间和压射比压保持较好的匹配，以防止压铸模设计的失败。