内浇道的英文

• ingate

• "内"英文翻译    inner; inside; within
• "浇"英文翻译    pour liquid on; sprinkle wat ...
• "道"英文翻译    road; way; route; path
• "内浇道宽度" 英文翻译 :    gate width
• "三角形内浇道" 英文翻译 :    triangular gate
• "顶浇雨淋式内浇道" 英文翻译 :    top pouring through pencil gates
• "直浇道横浇道内浇道面积之比" 英文翻译 :    sprue-runner-gate area ratio
• "浇道" 英文翻译 :    feeder; geat; pouring channel; pouring gate; runner gate; running channel; sprue cold material trap
• "内浇口" 英文翻译 :    cast gate; flow gate; in gate; ingate; parting line gate
• "下浇道, 竖浇道" 英文翻译 :    down gate
• "下浇道，坚浇道" 英文翻译 :    down gate; down sprue
• "边浇道" 英文翻译 :    side gate
• "横浇道" 英文翻译 :    cross gate; runner
• "坚浇道" 英文翻译 :    down sprue
• "浇道棒" 英文翻译 :    runner stick
• "浇道比" 英文翻译 :    runner ratio
• "浇道砖" 英文翻译 :    runner brick
• "开浇道" 英文翻译 :    spruing
• "热浇道" 英文翻译 :    insulated runner hot runner
• "竖浇道" 英文翻译 :    down gate; down sprue; sprue
• "外浇道" 英文翻译 :    sprue
• "无浇道" 英文翻译 :    runner less; runnerless
• "下浇道" 英文翻译 :    down sprue
• "直浇道" 英文翻译 :    downsprue; sprue
• "挡渣内浇口" 英文翻译 :    ball gate

• The cross - section area of the internal sprue , the fill speed , the fill time and injection pressure are important die casting technology parameters
  摘要内浇道截面积、充填速度、充填时间和压射比压都是重要的压铸工艺参数。
• Feeding , ingate design , air discharge , position of signal wire were analysed and discussed , aiming at the several questions in production of low pressure casting
  摘要根据低压铸造工艺的特点和生产实践，从补缩、内浇道设计、排气、信号线安放位置等方面进行了分析和探讨。
• Based on the new equilibrium solidification theory , the dispersed gate with flat 、 thin and wide rise neck , coupled with cold iron and warming riser , was adopted in the new gating system
  经分析主要原因是原工艺热冒口的冒口颈（内浇道）偏小，且开设的位置不合理，造成内浇道根部存在疏松和晶粒粗大铸造缺陷。
• The cross section area of the internal sprue of the die casting dies designed should be of proper value , and matches perfectly the fill speed , the fill time and injection pressure in case that the die casting dies fail in the design
  设计压铸模时应当确定恰当的内浇道截面积，并使之与充填速度、充填时间和压射比压保持较好的匹配，以防止压铸模设计的失败。
• In this paper , the software for the die casting technology parameters design is built based on the optimization of the die casting system matching , and is used for the design of the die casting technology parameters , such as the cross section area of the internal sprue , the fill speed and the fill time etc
  文章基于压铸系统匹配优化的思想，建立压铸工艺设计软件，使用软件进行内浇道截面积、充填速度和充填时间等压铸工艺参数的设计。
• The research showed that basin is the more important feeding resource than runner in runner type gating system in lost wax casting . therefore , on the basis of the basin as feeding resource , runner and ingate as feeding channel , a new design method for runner type pouring and feeding system in investment casting was developed . the corresponding feeding mathematical pattern and allowable total weight listed for casting cluster with different basin were established after analyzing the practical feeding of basin and the calculating process for design was described in detail
  在熔模铸造横浇道型浇注系统中，浇口杯是比横浇道更为重要的补缩源，因此在立足于浇口杯为补缩源、横浇道和内浇道为浇注补缩通道的基础上，开发了适用于熔模铸造横浇道型浇注补缩系统设计的新设计方法，在详细分析了浇口杯的实际补缩情况后，建立了相应的数学补缩模式和不同浇口杯的铸件组许用铸件总质量表，并具体介绍了设计计算过程。
• Considering of the problems exist in practice , large orifice discharge principle is employed to study the pressure distribution of ring runner system , the even ab lity for discharging of gates , the relationship of flow with the position of spr ue and the type of gates . a new design idea about circular runner system of cast is proposed
  根据生产中存在的问题，用大孔出流理论研究了环形横浇道系统的压力分布、内浇道出流均匀性及流量与直浇道引入位置和内浇道引入方式之间的关系，提出了圆形铸件环形横浇道系统新的设计思想。

• 内浇道的法语：attaque dirigée