分模的英文

• split die

• "分"英文翻译    component
• "模"英文翻译    mould; pattern; matrix
• "对分模" 英文翻译 :    split pattern
• "分模杯" 英文翻译 :    dividing mold cup
• "分模粉" 英文翻译 :    parting powder
• "分模剂" 英文翻译 :    parting agent; parting compound
• "分模面" 英文翻译 :    die parting face; die parting surface; flash land; mold joint; parting surface
• "分模砂" 英文翻译 :    parting sand
• "分模数" 英文翻译 :    submodule
• "分模线" 英文翻译 :    die line; die parting line; flash line; flask line; paring line; partingline; separating line; silhouette; split line
• "分模纸" 英文翻译 :    parting paper
• "切分模" 英文翻译 :    dividing die
• "半分模型" 英文翻译 :    pattern half
• "半分模样" 英文翻译 :    pattern half
• "部分模型" 英文翻译 :    department pattern
• "差分模式" 英文翻译 :    difference modes
• "差分模增益" 英文翻译 :    differential-mode gain
• "分模面飞轮" 英文翻译 :    split arm flywheel; split-arm flywheel; spoke-divided flywheel
• "分模造型" 英文翻译 :    parted pattern molding
• "积分模式" 英文翻译 :    integral mode
• "计分模板" 英文翻译 :    scoring stencil
• "可分模型" 英文翻译 :    part pattern; parted pattern
• "拼合线 分模线" 英文翻译 :    splitline
• "齐面分模线" 英文翻译 :    flush parting line
• "切边切分模" 英文翻译 :    trimming and dividing die

• P6 _ white pencil to give high light and part lines
  用白色的色阏剐加上光影和分模
• The fractue experimental research of maraging 350 torsional rods
  大型连杆分模面混晶及粗晶魏氏组织
• A rule - based method for automatic parting design of engine blade moulds
  基于规则的发动机叶片模具自动分模设计
• Can we add ejector sleeves or ejector pins in the boss of this part
  产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？
• There ' s an undercut at this position and it needs a slider . it will also have a parting line on this side , is that ok
  产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？
• When the pressure inside the mold cavity is too great , the mold opening force is greater than its clamping force . then , the mold will be forced to open and cause burr overflow
  当塑料在模腔内的压力太大，其分模力大于锁模力，因而迫开工模，就会产生毛边。
• According to the requirement of die designing , the die parting face and the gutter is designed . by boolean calculation , the blocker , finisher , cut - off die and stripper are generated
  根据锻模设计要求，设计了分模面、毛边槽，通过布尔运算，生成了预锻模、终锻模、切边模实体和卸料板。
• According to the structure of the final forging die , the flash groove is studied and coded into a separate sub - function . in order to split the upper and under dies , a sheet body of the separating surface is coded into a sub - function
  根据锻模设计要求，研究了分模面、毛边槽的设计并编制了相应模块；研究了锻模参数的计算和锻模实体的生成。