保压时间的英文

• dwell time
• pressure hold time
• pressure holding time

• "保压"英文翻译    pressurize; pressure maintai ...
• "时间"英文翻译    time; hour
• "试压保压时间" 英文翻译 :    holding time at test pressure
• "锻压时间" 英文翻译 :    forge time
• "积压时间" 英文翻译 :    assembly time
• "加压时间" 英文翻译 :    indentation time; pressing time; pressure dwell
• "减压时间" 英文翻译 :    decompression time
• "减压时间表" 英文翻译 :    ascent schedule
• "升压时间（秒）" 英文翻译 :    booster duration (sec)
• "停压时间" 英文翻译 :    dwell time
• "续压时间" 英文翻译 :    after-pressure time
• "预压时间" 英文翻译 :    squeeze time
• "增压时间" 英文翻译 :    booster time; pressurization time
• "总减压时间" 英文翻译 :    total decompression time
• "初始等压时间" 英文翻译 :    initial isobaric period
• "电压时间曲线" 英文翻译 :    volt time curve; volt-time curve; voltage time curve
• "堆积受压时间" 英文翻译 :    closed assembly time
• "高压时间试验" 英文翻译 :    high-voltage time test; high-voltagetimetest
• "焊接加压时间" 英文翻译 :    weld pressure time
• "预热加压时间" 英文翻译 :    preheat pressure time; preheating pressure time
• "注射升压时间" 英文翻译 :    injection boost time
• "保压" 英文翻译 :    pressurize; pressure maintaining◇保压阀 pressure retaining valve; 保压时间 dwell time (压铸)
• "电压时间特性曲线" 英文翻译 :    volt-time characteristic curve
• "击穿电压时间曲线" 英文翻译 :    voltagetime-to breakdown curve
• "收缩压时间指数" 英文翻译 :    systolic pressure time index; systolic pressure-time index

• Increase dose , holding time and holding pressure
  增加料量,保压时间和保压压力
• Raise holding time and pressure
  增加保压时间和保压压力
• Lower to note the pressure of mold , reduce to model and protect to press time
  降低注塑压力，减少成型和保压时间。
• 2 automatic rise and stable pressure . the stable pressure can be adjusted freely
  2自动回升，保压保压时间可任意调节。
• Hold up time
  保压时间
• When compressing , the proper pressure is between 7 - 11 t / cm2 , the keeping time is 60s or so
  磁体压制时合适的成型压力在7 11t cm ~ 2之间，合适的保压时间在60s左右。
• The important parameters such as pressing powder pressure , pressing speed and holding pressure time etc , will affect directly the quality of initiating explosive device
  压药压力、加压速度、保压时间等重要工艺参数都直接影响其质量。
• The researches represented that the main control factors affecting the quality of ied have : 1 ) the pressure of pressing powder ; 2 ) the rising rate of pressing powder pressure ; 3 ) the holding pressure time , except the right design and the material quantity used
  研究表明除与正确的设计、所用材料的质量等因素有关外,影响火工品压药质量的主要控制因素有: 1 )压药压力值; 2 )压药压力的上升率; 3 )保压时间等。
• It has shown that the combination with higher magnetic and mechanic properties of the bonded magnet is presented on the basis of proper curing process temperature , 120 cto 150 c , and the curing agent is and proper mold press , 500 - 600mpa , keeping press time is 20 seconds
  固化工艺中的固化温度不宜过低，应以120到150之间为宜。在压制过程中，模压压力为500 600mpa ，保压时间为20秒时可以使粘结磁体的密度达到最高值，且具有较好的磁性能和力学性能。
• During the temperature fields , the results indicate that the processing parameters such as the extrusion velocity , casting temperature , perform preheating temperature , die preheating temperature and so on are important for the temperature fields besides the dwell time . they are must be in concordance each other to the deforming zone is in the quasi - solid state , and the stable semi - solid extrusion is implemented . during the deforming fields , the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process , and the variations of the stress - strain fields are studied
  在温度场的模拟中，模拟结果表明，保压时间是影响制件成形质量的关键因素之一，挤压速度、液态金属浇注温度、预制体预热温度和模具预热温度等工艺参数对温度场的影响也很大，需进行参数之间的协调，只有当变形区内部始终维持准固态时，才能实现稳定的液-固挤压成形过程；在变形场的模拟中，根据液态浸渗挤压的成形特征，选用了双曲正弦刚-粘塑性有限元计算模型，研究了变形过程中应力应变场的变化规律，研究了模角对变形和金属流动的影响及变形力的变化过程和其影响因素。

• 保压时间的日语：ほあつじかん