齿轮啮合原理的英文

• principles of gear connection

• "齿轮"英文翻译    cogwheel; gear wheel wheel-l ...
• "啮合"英文翻译    clench the teeth mesh; engag ...
• "原理"英文翻译    principle; tenet; axiom; the ...
• "齿轮啮合" 英文翻译 :    catching of toothed wheels; gear engagement; gear meshing; gearing mesh
• "齿轮啮合边" 英文翻译 :    engaging side of gears
• "使齿轮啮合" 英文翻译 :    throw into gear
• "啮合原理" 英文翻译 :    theory of engagement
• "齿轮啮合间隙" 英文翻译 :    gear backlash
• "齿轮啮合节点" 英文翻译 :    pitch point
• "齿轮啮合效率" 英文翻译 :    gear mesh efficiency
• "盘车齿轮啮合" 英文翻译 :    turning gear piggy back
• "平稳齿轮啮合" 英文翻译 :    smooth tooth action
• "头档齿轮啮合" 英文翻译 :    first gear engagement; first-gear engagement
• "无齿轮啮合的" 英文翻译 :    ungeared
• "楔形齿轮啮合" 英文翻译 :    keilverzahnung straight spline
• "锥齿轮啮合的" 英文翻译 :    v and h check
• "内摆线齿轮啮合" 英文翻译 :    hypoid gearing
• "齿轮啮合误差测量仪" 英文翻译 :    gear meshing error meter
• "检查齿轮啮合涂色剂" 英文翻译 :    gear marking compound
• "这两个齿轮啮合在一起" 英文翻译 :    the two cogwheels are engaged
• "锥齿轮啮合调整衬垫" 英文翻译 :    bevel gear mesh adjusting gasket
• "针轮啮合" 英文翻译 :    pin gearing; pingearing
• "检查齿轮啮合型情况使用的涂色剂" 英文翻译 :    marking compound
• "闭合原理" 英文翻译 :    principle of closure
• "并合原理" 英文翻译 :    combination principle

• Exact modeling of gear teeth is based on meshing theory
  摘要根据齿轮啮合原理，建立了轮齿的精确齿形。
• Principles of gear connection
  齿轮啮合原理
• Based on conjunction theory , the models for gear manufacturing is developed , and the equation of the gear surface is gained by the equation of rack cutter . the contact line in manufacturing and the tooth profile of the gear is also discussed based on the equation of the gear surface
  本文首先基于齿轮啮合原理,建立了齿轮加工的模型,由刀具曲面方程推导出被加工齿轮的齿面方程,并进一步推导出齿轮端截面的齿廓方程和齿轮刀具接触线方程。
• The profile equation of whole profile meshing is worked out by the meshing theory , and the numerical calculation program of the new profile is accomplished . the 3d modeling of the gear rotor and the movement simulation of the gear assembly system are realized . the interference and sidegap of gear meshing are analysed by 3d modeling of the gear , so it can be judged that the gear profile is right whether or not before machining
  运用齿轮啮合原理，推导出全封闭齿廓啮合型面的齿形方程，完成齿形相应的数值计算程序，并对齿轮转子进行三维实体造型及齿轮装配体运动仿真的研究；用齿轮三维造型来进行装配模拟并分析啮合副装配的干涉和侧隙，在加工前就能对齿轮齿廓形状的正确与否进行判断。
• Based on the theories of gear engagement , contact analysis , friction and heat transfer , a three - dimensional finite element model of gear tooth was established to investigate temperature distributions and variations along the contact path over a range of applied loads and operating speeds with consideration of lubrication conditions . sensitivity analysis of surface temperature to gear configuration , frictional heat flux , heat transfer coefficients , and oil and ambient temperature was conducted and the major parameters influencing surface temperature were evaluated
  本文基于齿轮啮合原理、轮齿接触分析、摩擦学和传热学，以有限元分析方法和理论分析计算相结合为手段并以实验测量结果作为参考，建立了适用于工业应用并具有较高计算精度的高速齿轮传动轮齿温度分析的模型和方法，系统地分析了轮齿本体温度的大小和分布以及齿轮几何、载荷及转速和润滑冷却条件等对轮齿本体温度的影响。
• The main work and results are as followings . according to gear engagement principle , the math model of swing movable teeth drive is established . the engagement curve , engagement equation , relative speed between eccentric gear and movable teeth , and between movable teeth and internal gear are presented , and the gear equation of internal gear is presented
  取得了以下研究成果：根据齿轮啮合原理，建立了基于齿轮啮合原理的摆动活齿传动的数学模型，推导了偏心轮激波器与活齿、活齿与中心轮内齿圈的接触线方程、啮合方程、相对速度和中心轮内齿圈的齿形方程。