齿宽的英文

发音:

"齿宽"怎么读用"齿宽"造句

英文翻译手机版

breadth of tooth
breath of tooth
face width
facewidth
space of interval
tool breadth
tooth breadth
tooth width
width of tooth

"齿"英文翻译 tooth
"宽"英文翻译 wide; broad
"齿宽角" 英文翻译 : width angle
"大齿宽颌鲱" 英文翻译 : pellonula vorax
"大齿轮齿宽" 英文翻译 : wheel facewidth
"定子齿宽" 英文翻译 : tooth width
"蜗杆齿宽" 英文翻译 : worm face width
"蜗轮齿宽" 英文翻译 : face width
"小齿宽颌鲱" 英文翻译 : pellonula leonensis
"锥齿轮齿宽" 英文翻译 : face width of tooth in bevel gears and hypoid gears
"有效宽度（有效齿宽）" 英文翻译 : effective face width
"齿口鱼科" 英文翻译 : evermannellidae; sabertooth fishes
"齿廓" 英文翻译 : [机械工程] flank profile; tooth profile
"齿口鱼" 英文翻译 : sabertooth fish
"齿廓变位" 英文翻译 : profilverschiebung profile displacement
"齿口目" 英文翻译 : odontostomatida
"齿廓带" 英文翻译 : zones of schreger
"齿口螺属" 英文翻译 : odostomia
"齿廓角" 英文翻译 : profile angle
"齿口拉力强度" 英文翻译 : notched bar strength

例句与用法

Effective face width
有效宽度有效齿宽
Worm face width
蜗杆齿宽
The research result shows that the motor ' s torque will improved in lower voltage , when tooth width are not equal , and magnet conductivity of material is high
研究结果表明，当专用电机采用不等齿宽结构，或采用高磁导的软磁材料时，均有利于提高电机在低电压下的输出转矩。
Analyze the stresses distributing of helical gear in long direction using 3dcbem . optimize the shape of dentiform using cvm as the optimize algorithm . the result were satisfied
作者编制了斜齿轮前处理程序，应用边界元应力分析程序3dcbem分析了沿齿宽方向的轮齿接触应力的分布。
The world ' s largest primate , a 10 - foot - tall giant with inch - wide teeth , lived in southeast asia for many centuries alongside human beings , according to a leading researcher
一名重要研究者指出，全世界最庞大的灵长目动物，一种高10英尺、齿宽1英?的巨猿，曾与人类共同居住在东南亚长达数百年。
In order to solve the two problems , this paper adopts the method of reduced gradient to design precisely the parameter of friction and transmission ratio of gearbox and the gear teethes of the sixth gear of the second shaft
本文通过对多种解决方案的分析，选择了适当改变变速器一档传动比及二轴六档齿轮齿宽这一简单的方案使问题得到基本解决。
The equation of pressure angle , width coefficient , and contact ratio are calculated and the influences of these parameters on contact are analyzed . based on ordinary involute gear , the diametral deflection principle of curvilinear - tooth
最后针对现有文献的不足,研究了刀具压力角、齿宽系数和重合度等参数的计算方法,并分析了这些参数对弧齿线圆柱齿轮啮合的影响。
Through militia programs , the final plan is to change the transmission ratio of gearbox , the parameter of friction piece as well as the gear width of the sixth gear of the second shaft . finally , the parts of transmission system - clutch , gearbox , driving shaft , driving bridge are checked and the problems are solved
本文通过多目标规划，最终的优化方案是适当改变变速器传动比、摩擦片参数及二轴六档齿轮齿宽，最后对传动系各部件- - -离合器、变速器、传动轴、驱动桥等进行了校核，使问题得到妥善解决。
The method that the fuzzy optimal model is changed to ordinary optimal model by the optimal level cut sets is interpreted . as the model is a mathematical model of multi - objective optimization on minimizing volume and minimizing tooth width , the method that a multi - objective model transformed into a single - objective model is introduced
论文阐述了通过最优水平截集法实现模糊优化模型向常规优化模型转化的方法，由于该模型是一个以体积最小和齿宽最小为优的多目标优化设计模型，论文详细讨论了多目标优化模型向单目标优化模型转化。