销轴的英文

• axis pin
• bead
• clevis pin with head
• hinge pin
• pinned shan

• "销"英文翻译    melt cancel; annul
• "轴"英文翻译    axle; shaft
• "销轴承" 英文翻译 :    pin bearing
• "摆锤销轴" 英文翻译 :    hammer pin
• "舵销轴套" 英文翻译 :    sleeve for rudder pintle
• "浮子销轴" 英文翻译 :    float pin
• "活塞销轴承" 英文翻译 :    gudgeon pin bearing; piston pin bearing
• "活销轴套" 英文翻译 :    movable pin shaft sleeve
• "空心销轴" 英文翻译 :    hollow pin
• "连杆销轴" 英文翻译 :    pitman pin
• "曲柄销轴衬" 英文翻译 :    crank pin bush
• "曲柄销轴承" 英文翻译 :    crank pin bearing; crankpin bearing shell
• "曲柄销轴颈" 英文翻译 :    journal, crank pin
• "曲柄销轴瓦" 英文翻译 :    crankpin step
• "实心销轴" 英文翻译 :    solid pin
• "销轴锁紧" 英文翻译 :    lock clasp
• "止推销轴承" 英文翻译 :    kingpin bearing
• "主销轴承" 英文翻译 :    king-pin bearing
• "转向销轴线" 英文翻译 :    knuckle pin center line
• "活塞销轴承,耳轴销轴承" 英文翻译 :    gudgeon pin bearing
• "电动机座销轴" 英文翻译 :    motor base pin
• "连杆上端销轴" 英文翻译 :    connecting rod gudgeon; connectingrodgudgeon
• "曲柄箱销轴衬" 英文翻译 :    crank pin metal
• "十字头销轴承" 英文翻译 :    bearing of the cross head pin; cross head bolt bearing; cross head holt bearing; cross head pin bearing
• "竖臂支点销轴" 英文翻译 :    vertical arm fulcrum pin shaft

• The piston end of the rod is attached to the piston by the piston pin, or wrist pin .
  连杆的活塞端用活塞销或销轴安装在活塞上。
• Hydraulical excavators - shafts of the equipment
  液压挖掘机工作装置用销轴
• Anchor hook key bearing load observation system
  锚钩销轴载荷监测系统。
• Plain washers for clevis pins - product grade
  销轴用平垫圈
• Plain washers for clevis pins
  销轴用平垫圈
• Leaf chains ll series
  空心销轴链条
• The main parts in the upper structure that bear pressure are of pipe truss structure and pin shaft link
  本机上部结构的主要受压构件为管绗结构，销轴连接。
• The computing results of the thesis shows that qtjs 160t railway crane ' s carrier frame has met the intensity requirements . the local stress of the contact position of carrier frame , outriggers and pins is presented . the dangerous positions of the carrier frame are pointed out
  论文分析、计算结果表明， qtjs160t铁路起重机底架结构满足强度要求，论文给出了车架、支腿和销轴联接处的局部应力情况，指出车架在回转支承圈处存在应力集中部位。
• The optimum design of the beat back - impact crusher is proposed , which aims at the highest efficiency of the machine work . the optimum designed mathematics model of the main structural dimension of the crusher ( m , , xc , s , w 2 > ir ) is built with restraining conditions such as force condition , energy condition , hammer steady condition , no moving interference , strength of spin axle and bearing condition , upper limit and lower limit of the design variant condition etc . finally , an example is give to illustrate the efficiently of the method proposed
  在综合考虑影响破碎机效率的各因素的情况下，提出了满足以力，能量，锤头稳定性，几何条件，不发生运动干涉，转子轴和滚动轴承的强度等约束条件，建立了包含破碎机关键参数(锤头质量m ，轴心o到销轴锤头接触距离r ' ，四川大学硕士学位论文锤头质心到销轴与锤头接触点的距离拙，锤头与岩石碰撞到销轴与锤头接触点的距离s ，转子的速度。
• Through the powerful stuucture anslysis ability of ansys , the thesis creats the fea models of carrier frame , outriggers and pins seperately and has them combined . the carrier frame structure " s intensity is analyzed . nonliner contact analysis is applied to the contact position of carrier frame , outriggers and pins
  论文对ansys软件进行了简要的介绍，然后充分利用ansys强大的结构分析和接触分析功能，采用把车架、支腿和销轴分别建模，再把它们组合在一起的方法，对底架结构进行强度分析，对车架、支腿和销轴接触处进行非线性接触分析。

• 销轴的日语：リスト ピンスピンドル