铸造碳化钨的英文

• cast tungsten carbide

• "铸造"英文翻译    cast-on outwell; foundry; ca ...
• "碳化"英文翻译    carbonize; acieration
• "钨"英文翻译    tungsten; wolfram
• "铸造碳化钨粉" 英文翻译 :    casting tungsten carbide powder; foundry tungsten carbide powder
• "铸造碳化物" 英文翻译 :    cast carbide
• "铸态硬质合金 铸造碳化物" 英文翻译 :    castcarbide
• "碳化钨" 英文翻译 :    tc tungsten carbide; tungsten monocarbide; tungstencarbide; wolfram carbide; wolfram varbide
• "铸造碳素钢" 英文翻译 :    cast carbon steel
• "粒状碳化钨" 英文翻译 :    granular tungsten carbide
• "烧结碳化钨" 英文翻译 :    cemented tungsten carbide; diamondite; sintered tungsten carbide
• "碳化钨＝钴刀头" 英文翻译 :    tungsten carbide cobalt tool tip
• "碳化钨弹心" 英文翻译 :    tungsten carbide core
• "碳化钨刀片" 英文翻译 :    tungsten carbide blade
• "碳化钨粉" 英文翻译 :    tungsten carbide powder
• "碳化钨粉末" 英文翻译 :    tungsten carbide powder; tungsten-carbide powder
• "碳化钨敷层" 英文翻译 :    tungsten carbide coating; tungsten-carbide coating
• "碳化钨合金" 英文翻译 :    carbon tungsten alloy; diamondite; tungsten carbide alloy
• "碳化钨块" 英文翻译 :    tungsten carbide slug
• "碳化钨粒子" 英文翻译 :    tungsten carbide particle
• "碳化钨模具" 英文翻译 :    tungsten carbide die
• "碳化钨磨球" 英文翻译 :    tungsten carbide ball
• "碳化钨喷嘴" 英文翻译 :    tungsten carbide nozzle
• "碳化钨球" 英文翻译 :    tungsten-carbide ball
• "碳化钨陶瓷" 英文翻译 :    tungsten carbide ceramics
• "碳化钨铣刀" 英文翻译 :    tungsten carbide cutter

• It is preferable to use tungsten carbide of fine grain size for such build - up welding
  堆焊采用的铸造碳化钨颗粒，以细的为佳。
• Cast tungsten carbide
  铸造碳化钨
• Their lifetime can be prolonged if they are repaired with cast tungsten carbide powder
  采用铸造碳化钨修补后，可以延长使用寿命。
• The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied , and on the basis of this study , composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol . % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology . pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads
  本文研究了铸态cu20ni20mn和cu20ni35mn合金的时效硬化特性及其与铸造碳化钨的界面特性，并在此基础上以不同尺寸( 42 362 m )的铸造碳化钨颗粒为增强体，采用真空热压液相烧结技术制备了不同颗粒含量( 0 45vol . )的铸造碳化钨颗粒增强cu - ni - mn合金基复合材料；以不同粒度的sic为磨料，在不同载荷条件下利用销?盘磨损试验机测试了复合材料的二体磨料磨损性能。
• The results show that the composites were more wear resistant than the matrix , contributing to the " volume effect " and " size effect " , the wear resistance increases with the particle content and size . the composite shows better wear resistance than high chromium cast iron material especially in low load and fine abrasive test condition . the results also indicate that the composite strengthened by ageing treatment was more wear resistant than as - cast composite
  磨损试验结果表明，铸造碳化钨颗粒增强cu - ni - mn合金基复合材料具有比较高的抗磨料磨损能力，而且其耐磨性随着铸造碳化钨颗粒体积分数及尺寸的增大而提高，表现出了强烈的“体积效应”及“尺寸效应” ，尤其是在低载荷、细磨料磨损条件下，复合材料表现出更好的而寸磨性，即使与高铬铸铁( cr28 )相比也有很大程度的提高。
• The strength and wear resistance of diamond drill bits for petroleum exploitation will be increased considerably when cast tungsten carbide is applied and adheres to the substrate firmly with cast tungsten carbide of 80 - 200mesh as the skelton and copper alloy as the soldering material in a process of non - pressure immersion
  石油钻探行业用的金刚石钻头，用粒度为80 ? 200目的铸造碳化钨粉作骨架，采用无压浸渍工艺，以铜合金作钎焊料，将铸造碳化钨与基体牢固结合，强度、耐磨性大大提高。