进给率的英文

• feed rate
• feedrates

• "进给"英文翻译    feed
• "率"英文翻译    rate; ratio; proportion
• "横进给率" 英文翻译 :    infeed rate
• "燃料进给率" 英文翻译 :    fuel rate
• "进给率指示器" 英文翻译 :    feed rate indicator
• "生料进给率比" 英文翻译 :    ratio of raw feed rate
• "反比时间进给率代码" 英文翻译 :    inverse time feed rate code
• "补给率" 英文翻译 :    recharge rate; recharge ratio
• "自给率" 英文翻译 :    degree of self-sufficiency
• "进给" 英文翻译 :    [机械工程] feed◇进给传动 feed drive; 进给阀 induction valve; inlet valve [机械工程]; feed valve; masked inlet valve; 进给控制 feed control; 进给丝杠 feed screw; 进给速度 feed speed; feed velocity
• "持续补给率" 英文翻译 :    available supply rate
• "粮食自给率" 英文翻译 :    degree of food self-support
• "能值自给率" 英文翻译 :    emergy self-sufficiency
• "热量补给率" 英文翻译 :    heat return
• "食物可给率" 英文翻译 :    food acceptability
• "地下水补给率" 英文翻译 :    groundwater recharge rate
• "坏设备自给率" 英文翻译 :    percent of self supply of mechanical equipment
• "弹药持续补给率" 英文翻译 :    ammunition available supply rate
• "机械设备自给率" 英文翻译 :    percent of self-supply of mechanical equipment
• "大进给" 英文翻译 :    roughing feed
• "反进给" 英文翻译 :    backward feed
• "杆进给" 英文翻译 :    bar feed; bare feed
• "横进给" 英文翻译 :    cross feed; infeed; transverse feed; transversefeed
• "后进给" 英文翻译 :    back feed
• "进给板" 英文翻译 :    feed plate

• Test conditions for machining centres - part 6 : accuracy of feeds , speeds and interpolations
  加工中心检验条件第6部分：进给率速度和插补精度检验
• Usually , volumetric models or vector force models used for optimization of feedrate must be created to get the variable feedrate along the tool path
  通常必须创建切削体积模型或矢量力模型来优化刀具路径各段的进给率。
• Since there is a lack of scientific tools in practical process planning stages , feedrates of nc machining are selected based on previous experiences
  由于加工参数缺乏科学的选择工具，数控加工的进给率常根据加工经验设定。
• The model is tested by a typical die - cavity roughing , and shortening machining time and balancing cutting - load can be attained
  通过典型模具型腔的粗加工试验验证，证明该进给率优化策略不仅可以缩短加工时间，而且可以使加工载荷均匀。
• Considering the die - cavity roughing being a 2 . 5d cutting , a novel cutting force surface model is created based on orthogonal cutting tests
  鉴于模具型腔粗加工常采用2 . 5维加工，提出一种通过正交切削试验建立切削力曲面模型用于模具型腔粗加工进给率优选的新策略。
• Based on the cutting force surface model , a polynomial equation of side cutting depth and feedrate is created to calculate the feedrate of each cl data and the calculated feedrate value is written out with the g - code position data block to an updated version of the die - cavity
  基于切削力曲面模型，采用多项式拟合的方法构建刀具在许可切削力下的侧向切深和进给率的方程，根据建立的方程计算每个刀位点处的进给率并反写到初始的g代码文件中。