轴比例的英文

发音:

"轴比例"怎么读用"轴比例"造句

英文翻译手机版

x scalex
z scalez

"轴"英文翻译 axle; shaft
"比例"英文翻译 scale; scaling
"横坐标轴比例尺" 英文翻译 : scale of abscissa
"轴比" 英文翻译 : axial ratio
"标轴比" 英文翻译 : parameter ratio; parameter-ratio
"后轴比" 英文翻译 : rear axle ratio
"离轴比" 英文翻译 : oar; off-axis ratio
"长短轴比" 英文翻译 : axial ratio; ellipticity
"天线轴比" 英文翻译 : antenna axial ratio
"轴比补偿器" 英文翻译 : axial ratio compensator
"轴比偏振" 英文翻译 : axial ratio polarization
"比例" 英文翻译 : 1.(长度上缩小和放大的倍数) scale; scaling 比例是用一时代表一哩。the scale is an inch to the mile.2.(比率) proportion; ratio; proportionality 正比例 direct ratio [proportion]; 反比例 inverse [reverse] proportion; 常比例 constant ratio; 按调整后的比例 in adjusted proportions; 按比例发展 develop in proportion
"椭圆率圆轴比" 英文翻译 : ellipticity ratio
"椭率椭圆度椭圆率长短轴比" 英文翻译 : ellipticity
"按比例" 英文翻译 : in proportion; at the ratio; pro rata; by a ratio of 按比例制图 draw to scale; 按比例发展 develop in proportion; proportional development; 按比例放[加]大 scale; scaling-up; scale-up; 按比例分配 prorate; pro rata allotment; 按比例复制 reproduce to scale; 按比例划分 proportionment; 按比例回扣 pro rata rebate; 按比例计算 pro rata; 按比例减低 proportional reduction; 按比例均摊 pro rata average; 按比例扩大 scale-up; 按比例衰减 flat fading; 按比例缩小 scale; scaling-down; scale down; 按比例调整间距打字机 typewriter with proportional pitch; 按比例增加 scale-up; scale up
"比例,比率" 英文翻译 : rate
"比例,均衡" 英文翻译 : proportion
"比例／大小" 英文翻译 : scale／size
"比例；规模" 英文翻译 : scale
"比例泵" 英文翻译 : dosing pump; metering pump; proportional pump; proportioning pump; roportioning pump
"比例比" 英文翻译 : ratio
"比例臂" 英文翻译 : proportional arm; ratio arms; ratio-arm
"比例表" 英文翻译 : nbsp; schedule of proportion
"比例尺" 英文翻译 : 1.[测量学] scale; plotting scale; measuring scale; comparing rule; graphical units; proportional scale (地图上某线段与实地相应距离之比, 也叫“缩尺”) 这张地图的比例尺是四十六万分之一。 the scale of the map is 1: 460000.2.(绘图工具) architect's scale; engineer's scale
"比例带" 英文翻译 : proportional band

例句与用法

Lem two axis leveling control for proportional valves
自动找平控制器lem700两轴比例输出自动找平控制器
For the multiaxial proportional loading , the dispersion degree of fatigue cracks was low
在多轴比例加载条件下，裂纹分布的分散性较小。
Calculate the x position by determining which 114 . value in the array you are dealing with . 115
首先计算x ，用元素在数组中的位置乘上x轴比例因子。
The y - axis scaling factor is calculated on line 104 in the exact same way as in the bar chart example see
Y轴比例因子是在第104行计算的，方法和上面的柱状图使用的方法一样（请参阅
In this paper ， the stress - strain analysis and life prediction for the notched shafts were studied under multiaxial constant amplitude proportional loading
本文针对多轴比例恒幅加载情况下的缺口件进行了应力应变分析和寿命预测研究。
The fracture surfaces of multiaxial fatigue specimens under proportional and non - proportional multiaxial loadings were observed and analyzed by using a scan electron microscope
摘要利用扫描电镜对多轴比例和非比例载下的疲劳试样的断口面和外表面进行扫描观测分析。
Second , a few methods presented by some scholars were used to calculate the elasto - plastic strains and stresses at the notch tip subjected to proportional loading . at the same time , a new method is proposed to calculate the stresses and strain for the same specimen
第二，针对多轴比例加载的情况，对缺口件采用了多种已有的方法进行了弹塑性应力应变的计算，并提出了一个新的计算公式。