转向横拉杆的英文

发音:

"转向横拉杆"怎么读用"转向横拉杆"造句

英文翻译手机版

steering cross rod
steering tie rod
steering tie-rod
tension rod
track rod lever

"转向"英文翻译 lose one's bearings; get los ...
"横"英文翻译 harsh and unreasonable; perv ...
"拉杆"英文翻译 bar; straining beam; drawbar ...
"转向横拉杆轭" 英文翻译 : steering knuckle tie rod yoke
"转向横拉杆接头" 英文翻译 : steering cross rod jaw
"转向横拉杆总成" 英文翻译 : spurstange
"转向横拉杆球铰接头" 英文翻译 : tie rod end
"转向节横拉杆球节" 英文翻译 : steering knuckle tie rod ball joint
"转向拉杆和横拉杆总成" 英文翻译 : rod &link assy
"横拉杆" 英文翻译 : tie rod; tierod; track rod; waler; waling
"转向关节横拉杆接头油嘴" 英文翻译 : steering knuckle tie rod end pressure lubricator
"转向关节横拉杆接头总成" 英文翻译 : steering knuckle tie rod end assy
"转向关节横拉杆球节" 英文翻译 : steering knuckle tie rod ball joint
"转向节横拉杆接头油嘴" 英文翻译 : steering knuckle tie rod end pressure lubricator
"转向节横拉杆接头总成" 英文翻译 : steering knuckle tie rod end assy
"横拉杆接头" 英文翻译 : track rod end
"横拉杆球头" 英文翻译 : tie rod joint
"横拉杆总成" 英文翻译 : tie rod assy
"前桥横拉杆" 英文翻译 : front axle tie rod
"右横拉杆" 英文翻译 : right steering tie tod
"中间横拉杆" 英文翻译 : center link assy
"左横拉杆" 英文翻译 : left steering tie rod
"转向横轴" 英文翻译 : cross shaft
"横拉杆端接头" 英文翻译 : tie rod end
"横拉杆, 前轮连接杆" 英文翻译 : tie rod

例句与用法

Steering tie rod
转向横拉杆
The mechanism consists of a steering gear box , pitman arm , drag kink , tie rods , steering arms , and steering knuckles , the latter supporting the front wheels
该机构由转向器，转向垂臂，纵拉杆，转向横拉杆，梯形臂和转向节构成，转向节支承着前轮。
Then , an optimal design to minimize tyre wear is performed , which brings forward the way to reduce tyre wear through optimal choosing and modulating original deposition of double - link independent suspension and optimizing the cut point of track rodin
论文对双横臂独立悬架参数提出以减小轮胎磨损为优化目标，进行了优化设计。提出了通过优选、调整悬架初始位置状态，以及优化确定转向横拉杆断开点位置的方法，来减小轮胎磨损。
The kinematic performance of the macpherson suspension on a real vehicle is studied , and the changes of the front wheel alignment and the motion of the front wheel in the longitudinal and the transversal directions are figured . based on the requirements of general layout , a constrained optimization design model is set up with the steering cross rod ball joint position as the optimization variables ( design parameters ) , and the sum of steering cross rod length interference while the left front wheel turning and bouncing as the objective function . and the optimization results are worked out by programming on computer
针对一种实际车型上的麦弗逊式悬架，计算分析了转向轮跳动时前轮定位角和车轮横向、纵向滑移量的变化情况，并根据实际车型上麦弗逊式悬架的空间布置要求，建立了以转向横拉杆断开点空间位置坐标为优化变量，转向横拉杆断开点空间布置坐标可变化范围为约束条件，车轮转向和跳动时转向横拉杆长度干涉量为目标函数的约束优化设计模型。