继电器开关的英文

• relay switch

• "继电器"英文翻译    electric relay; relay
• "开关"英文翻译    Q-switching
• "继电器开关电路" 英文翻译 :    relay switching circuit
• "起动机继电器开关" 英文翻译 :    starter relay switch
• "电器开关" 英文翻译 :    electric switch
• "单独点火断电器开关" 英文翻译 :    individual ignition cut out switch
• "步进式开关继电器" 英文翻译 :    stepping switch type relay
• "开关操纵继电器" 英文翻译 :    switching relay
• "压敏开关, 压敏继电器" 英文翻译 :    pressure sensitive switch
• "自动开关, 自动继电器" 英文翻译 :    recloser
• "配有热继电器和电磁继电器的自动开关" 英文翻译 :    thermal magnetic breaker
• "闭路器开关" 英文翻译 :    circuit close
• "避雷器开关" 英文翻译 :    arrester switch
• "变光器开关" 英文翻译 :    dipping switch
• "变压器开关" 英文翻译 :    transformer switch
• "传感器开关" 英文翻译 :    sensing switch
• "传声器开关" 英文翻译 :    microphone switch
• "存储器开关" 英文翻译 :    storage switch
• "导向器开关" 英文翻译 :    director switch
• "调光器开关" 英文翻译 :    dimmer switch
• "调速器开关" 英文翻译 :    governor switch
• "断路器开关" 英文翻译 :    killer switch
• "蜂鸣器开关" 英文翻译 :    buzzer stop; buzzer switch
• "刮水器开关" 英文翻译 :    reading lamp switch; reading lamswitch; wiper control
• "刮雨器开关" 英文翻译 :    gua yu qi kai guan

• When the room temperature drops below a preset value, the thermostat switch closes turning on the furnace .
  当室温下降到低于预定值时，热继电器开关闭合，使炉子打开。
• Research and application of switch state testing of temperature delays
  温度继电器开关状态检测的研究
• The testing methods , hardware structures and software designs of the switch states for 512 temperature delays , as well as switch state bytes and block diagram of the application program to determine multiple switch states are introduced
  摘要从512支温度继电器开关状态的检测着手，介绍了温度继电器开关状态检测电路的硬件结构和软件设计思路。
• Abstract : the paper analysis control requires of the axial - flow compressor . in order to protect axial - flow compressor from the surging , using the programming single - loop adjuster ( its kernel is a microprocessor ) as the adjuster , comparing with the traditional analogy / digital adjusters , can make the system much simpler , more functional and more reliable
  文摘:分析了轴流压缩机工况的控制要求和控制方案.采用了以微处理器为核心的智能仪表? ?可编程型单回路调节器作为控制调节装置,与传统的模拟/数字调节器和继电器开关组合的方式比较,系统构成简单,控制功能强,可靠性高,为实现轴流压缩机防喘振控制提供了一种集约式设计方案
• There are two functions in the fault injector , one is the realization of digital controller ’ s work environment by simulating the electrical characteristics of sensors and actuators , another function is the control of the fault injection which is realized by the voltage - controlled constant voltages source and relay switch circuit etc . the manage compuer is in charge of the fault mode setting , fault injection process controlling and result data retrieving
  在故障注入器上,通过对传感器和执行机构电气特性的模拟提供控制器的运行环境,利用压控恒压源和继电器开关等电路实现多种故障注入方法;作为故障注入器上位机的管理计算机,负责故障模式设置、故障注入过程控制和结果回收处理。
• As to the software , we firstly scheduled all of the test signal path between the computer and the uut , the output control logic between the digital i / o card and programmable relay key matrix , and used all of this to be the base of software design , then we introduce the block flow of software
  在软件设计部分首先规划了所有测试信号在计算机主机与被测件之间的连接和传输路径、数字i / o卡对可编程继电器开关矩阵的输出控制逻辑，作为软件设计依据，随后介绍了软件的模块化设计思想。
• This paper first begin with the connotation of virtual instrument technology , study and discuss the criterion and the working theory of usb deeply . on the principle of usb1 . 1criterion , using usb interface chip usbn9604 and low consumption mirochip c8051f231 , we designed the available interface of usb bus and its controlling software , turn the communicating function based usb bus between computer and testing device . second based on the developed interface of usb bus , using microchip pic16c62 and a mount of relays , we designed the multiswitching scanner and its controlling software to complete the funtion of accesses swithing in testing system . third calling the api function inside the windows using vb programming language , communicat with the impelling program of selected hid , achieve the function of testing instrument with usb interface , complete the development of upside software faced testing . at last , based on the deep studying of pcb testing method , used the developed multiswithing scanner and software faced testing , combinated with necessary testing instrument , we constructed the pcb testing system and analized the testing result simply
  论文首先从虚拟仪器的技术内涵出发，深入研究和讨论了通用串行总线usb规范及工作原理，并依据usb1 . 1规范，采用usb接口芯片usbn9604和低功耗微处理器c8051f231设计开发了通用的usb总线接口及其控制固件，实现了通用计算机与测试设备之间基于usb总线的通信功能；其次，在所开发的usb总线接口的基础上，使用微处理器pic16c62和多路继电器开关，设计开发出实现测试系统中测试通道切换功能的多路通道扫描器及其控制固件；再次，采用vb语言编程，调用windows内部api函数，与选定hid类驱动程序进行通信，实现usb总线接口测试仪器功能，完成面向测试的上层软件开发；最后，在深入研究印刷电路板测试方法的基础上，利用已开发的多路通道扫描器和面向测试软件，结合必要测试仪器组建印刷电路板测试系统，并对测试结果进行了简要的误差分析。

• 继电器开关的日语：けいでんきスイッチ リレースイッチ