程序运算的英文

• program operation
• programmed algorithm
• sequential operation

• "程序"英文翻译    procedure
• "运算"英文翻译    operation; arithmetic; opera ...
• "源程序运算" 英文翻译 :    source program operation
• "程序运算分析" 英文翻译 :    program operation analysis
• "汇编程序运算符" 英文翻译 :    a embler operator; assembler operator
• "例行程序操作子程序运算" 英文翻译 :    routine operation
• "可编程序运算放大器" 英文翻译 :    programmable mable operational amplifier; programmable operational amplifier
• "可编程序运算放大器电路" 英文翻译 :    programable operational amplifier circuit
• "按序运算" 英文翻译 :    sequential operation
• "顺序运算符" 英文翻译 :    sequential operator
• "程序运行" 英文翻译 :    program execution; program running
• "逐程序运行" 英文翻译 :    steover
• "子程序运行" 英文翻译 :    subprogram activation
• "程序运行方式" 英文翻译 :    program run mode
• "汇编程序运行" 英文翻译 :    a embly run; assembly run
• "基准程序运行" 英文翻译 :    benchmark run
• "监督程序运行" 英文翻译 :    monitor run
• "程序运行的效率" 英文翻译 :    vba
• "多道程序运行系统" 英文翻译 :    multiprogramming operation system
• "符号调试程序运行" 英文翻译 :    symbolic debugger operation
• "连接编辑程序运行" 英文翻译 :    linkage editor run
• "目标程序运行时间" 英文翻译 :    object program time
• "时序操作 顺序操作 顺序运算" 英文翻译 :    sequentialoperation
• "运算程序" 英文翻译 :    operating program; operational program; operational sequence; operator routine; production program
• "运算程序库" 英文翻译 :    algorithm library; arithmetic library

• The simulation program was complied under the real - time simulation support system , asca
  在实时仿真支撑系统asca下编写了计算程序，通过改变程序运算速度达到实时的需要。
• Then , with comparing and analyzing , three examples are taken to verify the reliability of the calculation method and the result of program in this paper
  并且用三个算例对比分析来检验计算方法及程序运算结果的可靠性。
• Note 1 : don ' t make buildings too specialized in look ? it ' s a bit the same rule than ships , although more flexible -
  注意1 ：建造建筑物时不要过度追求视觉效果? ?建筑物的程序运算法则比飞船的运算法则来的简单，虽然它有更大的灵活性。
• They will probably get instanced in cities and use special procedural algorithms ( ala gta ) to not require too much server bandwidth
  它们会出现于城市当中，我们会使用一些特别的程序运算方式（像gta那种） ，把服务器带宽的要求降到最低。
• The result indicates that this program is safe and reliable for pdew fuzzy optimization . the researching in this paper has been obtained some worth in fuzzy optimization design and motions of pdew
  以某橡胶厂轮胎硫化机弧面蜗杆减速器为例，验证了该模糊优化设计程序，结果表明该程序运算准确可靠，优化结果可行。
• How to make the design flow accord with actual situation needs inquiring into . this paper presents a simple calculation formula based on probability method with studying the hunter ' s method and russian method deeply
  本文采用概率方法，运用程序运算分别对美国亨特方法和俄罗斯现行规范采用的方法进行了深入探讨，并在此基础上提出了符合实际情、计算简单方便查阅的计算公式。
• In order to view the results of computing in effect , the paper alse discusses the three dimension visualization . due to the opengl ' s ability and efficiency in 3 - d program , the paper discusses the theory of opengl in detailed , simultaneously discusses the programming process and realizing method
  为了能够有效的显示程序运算结果，论文还讨论了三维显示的问题，由于opengl技术在三维显示上的有效性与灵活性，论文详细讨论了opengl技术原理与三维显示实现的过程和方法。
• For better veracity of simulating model , model is used lookup - table module to calculate the thermodynamic character of refrigerant , and datas of experience and test is combined in the compressor module , also the coefficient of heat transfer changing by running parameter is decided by computational procedure . in addition , choosing congruence step size solves the divergence of simulation procedure
  为了使仿真模型具有相当的准确性，模型中采用查表模块进行制冷剂热力性质计算，压缩机模块中将实验数据与经验计算数据相结合，通过程序运算确定冷凝器和蒸发器传热系数与运行参数之间的关系，并成功解决了仿真程序运行发散的问题。
• At the same time adopting the single factor analytic approach , changing the rigidity and damping of fore - suspension and rear - suspension separately , using the simulation calculation procedures that are designed to carry on operational analysis , the optimization values of fore - suspension and rear - suspension parameters are gotten . compared the results that the simulation calculation procedures operated the optimization values with the simulation result before optimization , the effect is relatively good
  同时采用单因素分析法，分别改变前、后悬架的刚度和阻尼，利用所设计的程序进行运算分析，得到前、后悬架参数的优化值，并将所有优化后的参数值代入计算程序运算后得出的结果与优化前的模拟计算结果比较，发现优化后效果较好。
• Using the digital technology improves the performance traditional thyristor welding machine , according to the characters of the double inverse star from rectifier circuit , set the parameters with micro - controller accurately , design the dependable trigger circuit , lead the feedback of voltage for the operation program , so the voltage of main circuit be carried out very steadily
  摘要利用数字控制技术对传统晶闸管焊接电源进行改进，根据双反星型晶闸管整流电路的特点，采用单片机进行精确设定，设计了高可靠性触发回路，结合电压反馈进行程序运算控制，实现了主电路输出电压的精确调整和可靠运行。