相位调整的英文

• phase adjustment
• phase control
• phase-control
• phasing adjustment
• phasing control
• space phasing

• "相位"英文翻译    phase position; phase
• "调整"英文翻译    adjust; tune-up; trim; trimm ...
• "场相位调整" 英文翻译 :    field phase control
• "声相位调整" 英文翻译 :    acoustic phasing
• "相位调整器" 英文翻译 :    desynchroniser; phase adjuster; phase regulator; phase shifter
• "比特相位调整" 英文翻译 :    bit phasing
• "彩色相位调整" 英文翻译 :    color phase control
• "电压相位调整" 英文翻译 :    regulation of voltage phase
• "定相相位调整" 英文翻译 :    phasing
• "脉冲相位调整" 英文翻译 :    pulse phasing
• "扫描相位调整" 英文翻译 :    phasing of the scan
• "设备相位调整" 英文翻译 :    set phase control
• "相位调整电路" 英文翻译 :    phase adjusting circuit; phase-adjusting circuit; phase-control circuit
• "相位调整叠加" 英文翻译 :    phe-adjustment stack
• "信道相位调整" 英文翻译 :    channel phasing
• "自动相位调整" 英文翻译 :    automatic phase control
• "相位扭动；定相；相位调整" 英文翻译 :    phasing
• "会聚电压相位调整" 英文翻译 :    convergence phase control
• "相位调整校正器" 英文翻译 :    desynchroniser corrector
• "移相器，相位调整器" 英文翻译 :    phase shifter，phs
• "导频色同步脉冲相位调整" 英文翻译 :    pilot burst phase adjustment
• "负载时电压相位调整器" 英文翻译 :    on load voltage and phase regulator
• "加载电压相位调整器" 英文翻译 :    on-load voltage and phase regulator
• "可旋相位调整变压器" 英文翻译 :    rotatable phase-adjusting transformer
• "场相位调节" 英文翻译 :    field of control; field phase control

• Knife shaft can be 360 degree adjusted by electric control
  刀轴可做360度电动控制相位调整。
• Knikfe shaft can be 360 degree adjusted by electric control
  刀轴可做360电动控制相位调整。
• These adjust the linearity and carry out small phase adjustments
  这些电池调整线性和执行小的相位调整。
• Apc automatic phase control
  自动相位调整
• This can be useful when the correct adjustment cannot be carried out through amplitude , threshold and phase adjustment
  通过振幅，开端和相位调整，当正确的调整不能被执行时，这个能有用。
• The difference clock delay match technology adjusts the two channel ad analog clock phase and implements the two way ad uniformly - space sampling
  差分时钟延迟匹配技术通过对两路ad的采样时钟进行相位调整,实现了两路ad的等间隔采样。
• When the phase is changed , the used phase transformers is voltage - control phase transformer which is changed by phase transformer consist of ordinary operation amplifier consist of ordinary operational amplifier
  在相位调整时所运用的移相器是由普通运算发大器构成的移相器改造成的压控移相器。
• The upper slotting / crease shaft is using automatic plane minor adjustment sysem , also allow roational adjustment of 360 degrees whatever operating or stop . the slotting shaft also using zero - storing system
  上刀轴装设平面式自动微调装置,刻度清晰,不论运转或停上均可做360相位调整,刀轴及附自动归零装置。
• The 33220a external frequency reference lets you synchronize to an external 10 mhz clock , to another 33220a , or to an agilent 33250a . phase adjustments can be made from the front panel or via a computer
  33220a外部频率基准使您能同步于外部10mhz时钟另一台33220a ,或agilent33250a .相位调整可从前面板或通过
• This method link amplitude adjust with phase adjust together , and perform coordinate control . by the simulation principle , the ct error compensation can be realized through operational amplifier , integrate circuit , fet , and other electronic component
  这种方法将电流互感器的相位调整和幅值调整结合到一起，进行协调控制，运用模拟原理，并采用运算放大器，场效应管等电子器件实现了电流互感器的误差补偿。

• 相位调整的日语：フェーズアジャストメント いそうちょうせい