电压上升率的英文

• rate of voltage rise
• voltage build-urate

• "电压"英文翻译    voltage; electric tension; e ...
• "上升"英文翻译    rise; go up; ascend
• "率"英文翻译    rate; ratio; proportion
• "再击穿电压上升率" 英文翻译 :    rate of rise restriking voltage
• "气压上升率" 英文翻译 :    pressure rate of climb
• "暂态恢复电压上升率" 英文翻译 :    rate of rise of transient recovery voltage
• "电压上升" 英文翻译 :    voltage build up; voltage rise
• "再闪荤压上升率" 英文翻译 :    rate of rise of restriking voltage
• "电压上升速度" 英文翻译 :    rate of voltage rise
• "绝对电压上升" 英文翻译 :    absolute voltage rise
• "次级电压上升时间" 英文翻译 :    secondary output voltage; secondary voltage rise time
• "电压临界上升率" 英文翻译 :    critical rate of rise of off state voltage
• "上升率" 英文翻译 :    altitude rate; ascension rate; climbing rate; escalating rate; positive rate of climb; rate of ascent; rate of rise; vertical climb rate
• "断态电压临界上升率" 英文翻译 :    critical rate of rise of off-state voltage
• "气压上升区" 英文翻译 :    anallobar
• "标称上升率" 英文翻译 :    nominal rate of rise
• "单发上升率" 英文翻译 :    single-engine rate of climb
• "负荷上升率" 英文翻译 :    load up variation; load uprise
• "负上升率" 英文翻译 :    negative rate of climb
• "脉冲上升率" 英文翻译 :    pulse rate of rise; rate of pulse rise
• "起始上升率" 英文翻译 :    initial climb rate
• "上升率变小" 英文翻译 :    loss of climb
• "上升率记录" 英文翻译 :    time-to-altitude record
• "上升率控制" 英文翻译 :    rate-of-climb control
• "上升率特性" 英文翻译 :    rate-of-climb characteristics

• Voltage build - up rate
  电压上升率
• In view of this situation this article has conducted research to the design of metallurgy auxiliary biography with the frequency conversion table electrical machinery first multianalysis to the frequency changer and the frequency conversion table electrical machinery movement characteristic is carried out , the voltage waveform harmonious which the frequency changer outputs is big , attacks in a big way , and the voltage climbing rate reaches as high as 6600v / mu s which is 20 times ordinary sine alternating voltage , the rolling mill auxiliary biography table set the extremely strict request to the electrical machinery ; its movement frequency is very low , rate frequency in 8 - 20hz ; the velocity modulation scope is wide , the lowest movement frequency lowers to 1hz , and the starting number of times is quite frequently , each hour reaches as high as 600 - 800 time , the impact shoulders in a big way , the overload capacity request is high
  针对这一情况本文对冶金辅传用变频辊道电机的设计进行了系统研究。首先对变频器和变频辊道电机的运行特性进行详细分析,变频器输出的电压波形谐波大,冲击大,电压上升率高达6600v / s ,是普通正弦交流电压的20倍;轧机辅传辊道对电机提出了十分严格的要求:其运行频率很低,额定频率在8 - 20hz ;调速范围宽,最低运行频率低到0 . 5hz ,起动次数相当频繁,每小时高达600 - 800次,冲击负荷大,过载能力要求较高。