焊透的英文

发音:

"焊透"怎么读用"焊透"造句

英文翻译手机版

complete fusion
complete penetration
full penetration of weld
fusion penetration
through welding
through-welding
weld penetration

"焊"英文翻译 weld; solder
"透"英文翻译 penetrate; pass through
"焊透侧" 英文翻译 : penetration side
"焊透度" 英文翻译 : weld penetration; weldpenetration
"焊透率" 英文翻译 : penetration rate
"焊透性" 英文翻译 : penetrability
"全焊透" 英文翻译 : complete penetraction and fusion in welding; complete penetration
"未焊透" 英文翻译 : inadequate penetration; inadequatepenetration; incomplete fusion; incomplete lack of fusion; incomplete penetration/ lack of penetration; insufficient fusion; non fusion; poor penetration
"不完全焊透" 英文翻译 : incomplete fusion; incomplete penetration; lack of fusion
"层间未焊透" 英文翻译 : incomplete inter-run penetration
"根部焊透层" 英文翻译 : root penetration
"根部未焊透" 英文翻译 : incomplete root penetration; lack of root fusion; lack of root penetration
"焊透深度" 英文翻译 : weld penetration
"接头焊透层" 英文翻译 : joint penetration
"接头焊透度" 英文翻译 : joint penetration
"接头未焊透" 英文翻译 : lack of joint penetration
"没有焊透" 英文翻译 : nonfusion
"全焊透焊缝" 英文翻译 : full-penetration weld
"全焊透角接" 英文翻译 : full penetration corner joint
"完全焊透" 英文翻译 : complete penetration; full penetration (welding); good penetration
"未全部焊透" 英文翻译 : incomplete penetration
"部分焊透焊缝" 英文翻译 : partial penetration weld; partial-penetration weld
"穿进速率焊透率" 英文翻译 : penetrationrate
"焊穿，焊透深度，熔深" 英文翻译 : weld penetration
"接头部分焊透" 英文翻译 : partial joint penetration

例句与用法

Partial penetrated butt weld
不焊透对接焊缝61
Internal defects : lack of penetration , lack of fusion , slag , gas pole , carck , overheating
内部缺陷：未焊透、未熔合、夹渣、气孔、裂纹、过热。
All welds shall be full penetration and continuous unless otherwise specified on the drawing
除非图上另外标明，所有焊缝均为连续全焊透焊接。
Electrical installations in ships - part 390 : cable penetrations - fire type test procedure
船上的电气安装.第390部分:电缆的熔焊透.着火型试验过程
Specification for welding primers and weld - through sealants , adhesives and waxes for resistance welding of sheet steel
板材钢电阻焊用焊接底剂焊透密封剂粘合剂和蜡规范
Diamond core drill can be laser welded with full penetration and the bonding strength is 1500 n / mm2 . dendrite morphology and porosity formed in the welds of al - fe - v - si aluminum alloy
用本激光器对金刚石薄壁钻进行焊接，可以将其完全焊透，抗弯强度为1500n / mm ~ 2 。
It has mang virtues such as weld moulding beauty , weld quanlity credibility and so on , espcially it can conquer not weld fully , not fusion and so forth fatal vice
它具有焊缝成型美观、焊接质量可靠等优点，特别是对克服常规焊接方法中的未焊透、未熔合等危险性缺陷具有重要意义。
The commonly used methods of connections , especially the high - strength bolted connection and welding with bolting mixed connections are discussed in more detail . the analysis for the problems , such as partial penetrated butt weld and welding deformation is also discussed in the paper
对工程中采用较多连接如高强度螺栓连接、栓-焊混合连接等作了较深入分析；对工程中容易出现问题连接如不焊透的对接焊缝计算方法及可能出现的焊接变形及处理等问题也作了较深入探讨。