焊接区的英文

• bonding area
• bonding pad
• weld area
• weld zone
• welding zone
• weldingzone
• weldzone

• "焊接"英文翻译    weld; welding; soldering; se ...
• "区"英文翻译    H region; H
• "焊接区保护" 英文翻译 :    weld shielding
• "冶]焊接区晶间腐蚀" 英文翻译 :    welddecay
• "焊接区保护 焊接熔池保护" 英文翻译 :    weldshielding
• "对接区" 英文翻译 :    docking area
• "分接区" 英文翻译 :    tapping zone
• "换接区" 英文翻译 :    shifting zone
• "汇接区" 英文翻译 :    tandem area
• "交接区" 英文翻译 :    cross connecting area; cross connecting district; cross connection area; cross connection district
• "连接区" 英文翻译 :    connected region; continuation area; linking section
• "邻接区" 英文翻译 :    adjacent country; adjoining region; contiguous area; contiguous zone
• "桥接区" 英文翻译 :    bridge region
• "终接区" 英文翻译 :    termination area
• "转接区" 英文翻译 :    transit area
• "侧面衔接区" 英文翻译 :    lateral overlapping
• "大区转接区" 英文翻译 :    regional transit area
• "混合芽接区" 英文翻译 :    mixed budded area
• "口咽连接区" 英文翻译 :    junctional region with oropharynx
• "连接区,j区" 英文翻译 :    joining region
• "连接区封锁" 英文翻译 :    junctional seal
• "连接区域" 英文翻译 :    attachment area
• "链接区段" 英文翻译 :    chained sector
• "邻接区, 毗邻区" 英文翻译 :    adjacent area
• "邻接区域" 英文翻译 :    adjacency areas

• Install exhaust pipe at soldering area
  安装排气管于焊接区。
• Method of bend test for stud welds
  柱杆焊接区弯曲试验方法
• Standard test method for performing tension tests on glass - fiber reinforced concrete bonding pads
  玻璃纤维增强混凝土焊接区的拉伸性能试验的标准试验方法
• The main contents include : with combination of z - n pid self - tuning formula and relay self - adaptation control methods , the pid parameters of weld area of furnace is given automatically
  论文研究工作主要包括：结合z ? npid自整定公式和继电自整定控制方法，自动整定加热炉焊接区的pid参数。
• Abstract : after anticorrosion metal - power spray welding was carried out for prevention of corrosion , the matched anticorrosion electrode is used to make backing weld . the new process can replace the traditional process wi th internal repaired mouth
  文摘:管道焊前对管端进行耐蚀金属粉末喷焊防腐，然后采用与之匹配的耐蚀焊条打底焊，从而取代焊后焊接区内补口防腐的传统施工工艺，达到了管道焊后可不再进行内补口防腐。
• The results of the experiments show that the ti3al - tcll dual alloys , by vacuum - electron - beam weld , hot die forging and 680c / 12h , ac , heat treatments , have satisfied synthesis properties of intensity , plasticity , hardness . and also it is the feasiblie way . this will establish the supporting technology for the manufacture of the compress disk in the areoengine
  实验结果表明，经真空电子束焊接ti _ 3al ? tc11双合金经过热模锻造和680 12h , ac或815 1h + 700 8h , ac热处理后，焊接区组织过渡均匀，可以使得焊缝处强度在室温拉伸时高于ti _ 3al ，而在600拉伸时高于tc11合金，获得强度、塑性、硬度均令人满意的综合性能，且是一条可行的工艺路线。
• Meanwhile it retains evenness on lift force to prevent leakage of residue that is caused by installation clearance error or changes in welding criteria , flow off molten iron as well as break - over welding , so that the ideal fosion depth and finishment have been fulfilled
  在需原动力的条件下，该机利用弹性夹角变化，随着筒体转动，使垫层焊剂始终紧贴筒体外侧环向焊接区，并保持托力均匀防止因装配间隙误差或焊接规范变化而引起漏渣，铁水下淌及焊穿现象，达到理想的熔深度和光洁度。

• 焊接区的日语：ボンディングパッド ウェルドゾーン せつごうりょういき ボンディングランド ようせつぶい ようせつぶ