温度的分布的英文

• pattern of temperatures

• "温度"英文翻译    temperature
• "的"英文翻译    4次方是 The fourth power of 2 i ...
• "分布"英文翻译    distribute; spread; scatter; ...
• "细分度的分布" 英文翻译 :    fine scaled distribution
• "云量按高度的分布" 英文翻译 :    vertical distribution of cloud
• "温度与盐度的分层状况" 英文翻译 :    stratification of temperature and salinity
• "温度的" 英文翻译 :    thermometric
• "速度的分解" 英文翻译 :    resolution of velocity
• "夜间臭氧垂直方向的分布不同高度的臭氧浓度" 英文翻译 :    night-time ozone profile
• "场的分布" 英文翻译 :    field distribution
• "点的分布" 英文翻译 :    scatter of points
• "风的分布" 英文翻译 :    wind distribution
• "根的分布" 英文翻译 :    root distridution
• "归并的分布" 英文翻译 :    merged distribution
• "回流的分布" 英文翻译 :    distribution of reflux
• "基牙的分布" 英文翻译 :    destribution of abutment
• "疾病的分布" 英文翻译 :    distribution of disease
• "井的分布" 英文翻译 :    well distribution
• "力的分布" 英文翻译 :    distribution of forces
• "煤的分布" 英文翻译 :    coal distribution
• "能流的分布" 英文翻译 :    power flow distribution
• "皮节的分布" 英文翻译 :    distribution of dermatome
• "评分的分布" 英文翻译 :    distribution of grading
• "热流的分布" 英文翻译 :    distortion of heat flux
• "雄花的分布" 英文翻译 :    male flower distribution

• Radial temperature distribution in production oil wells
  生产油井井下径向温度的分布
• The effect of pr on distribution of temperature is evidently
  管道内温度的分布与pr数密切相关。
• Thermal fe analysis can predict punch and die temperature distribution during the cooling process . holes drilled in the die allow for faster cooling
  温度有限元分析可以预测冷却过程中冲床和模具温度的分布，模具中冲孔的冷却速度比较快。
• In chapter 3 , it systematically analyzes the bi - dimensioned instantaneous temperature range state of piston , cylinder liner and piston rings when diesel engine type 4135 is considered under the normal friction heat
  第3章系统地分析了4135柴油机在考虑摩擦热的正常工况下活塞、缸套和活塞环各部分二维瞬态温度的分布和状态。
• The body comfort index is established . at the same time , the dekad apparent temperature distributing character of all over the country were calculated and analyzed based on many years average weather data of 198 stations
  同时利用全国198站多年平均气象资料计算分析了全国旬体感温度的分布特征，以此为基础进行了全国人体舒适度的区划，并利用地理信息系统做出旬区划图。
• In effect , bodies are assumed rigid and treated as point massed ; sprigs are massless and electrical leads resistanceless , suitable corrections are made to the system mass or resistance ; temperature are uniform ; etc
  在效果上，物体被假设为是刚体并且质量都集中在一点上，弹簧的质量可以忽略；导线的电阻为零；或者是可以得到合适的关系式使得系统的质量、电阻和温度的分布是均匀的。
• The melt velocity far from the gate was found to be higher than that near the gate during the compression stage contrary to that of conventional injection molding ( cim ) resulting in different part residual stress and melt temperature distribution
  在压缩阶段离胶口较远的熔胶速度会比离胶口较近的熔胶速度来的快，这种现象与传统射出成型是相反的，也因此导致残馀应力与熔胶温度的分布与传统不同。
• The melt velocity far from the gate was found to be higher than that near the gate during the compression stage contrary to that of conventional injection molding ( cim ) resulting in different part residual stress and melt temperature distribution
  在压缩阶段离胶口较远的熔胶速度会比离胶口较近的熔胶速度来的快，这种现象与常规射出成型是相反的，也因此导致残余应力与熔胶温度的分布与常规不同。
• The results show that , the distribution of temperature during laser sintering process has a great effect on “ balling ” phenomena of the laser sintered metal part . optimizing the distribution of temperature , which can be realized by changing laser processing parameters , is an effective way to decrease the “ balling ” effects
  将分析结果与试验结果对比表明, “球化”效应与温度的分布有很大的关系,通过改变工艺参数优化温度场可以有效降低烧结件“球化”效应。
• The paper establishes mathematics model of electromagnetic heating system of eddy current field and temperature field , and gives corresponding discrete format with elements as eight nodes , hexahedron equal cell , through calculating eddy - current field to gain the internal heat source that the temperature field needed , to use discrete method to solve the problem of induction - heating part ' s temperature field by axial symmetrical electromagnetic , and then to analyze the characteristic of instantaneous temperature field
  本文建立了电磁加热系统的涡流场和温度场间接耦合的数学模型，分析了不同频率下涡流和温度的分布情况，并以八节点六面体等参元为例给出了涡流场对应的离散格式，通过计算涡流场获得温度场所需要的内热源强度，加热部件的温度场以轴对称格式进行离散求解，并对瞬态温度场有限单元法的求解特点进行了分析。