注射压力的英文

发音:

"注射压力"怎么读用"注射压力"造句

英文翻译手机版

injection pressure

"注射"英文翻译 injection; inject; get a sho ...
"压力"英文翻译 pressure; tension
"注射压缸" 英文翻译 : injection cylinder
"注射压机" 英文翻译 : injection press
"反射压力" 英文翻译 : reflected pressure
"辐射压力" 英文翻译 : radiation pre ure; radiation pressure
"抛射压力" 英文翻译 : throw pressure
"喷射压力" 英文翻译 : expulsion pressure; injection pre ure; injection pressure; jet pressure; nozzle pressure
"喷射压力表" 英文翻译 : injection pressure gauge
"喷射压力机" 英文翻译 : ejecting press
"声发射压力" 英文翻译 : acoustic radiation pressure
"声辐射压力" 英文翻译 : acoustic radiation pressure
"酸喷射压力" 英文翻译 : acid-injection pressure
"注射压缸温度" 英文翻译 : injection cylinder temperature
"辐射压力天平" 英文翻译 : radiation pressure balance
"聚焦辐射压力" 英文翻译 : focused radiatn pressure
"空气喷射压力" 英文翻译 : air injection pressure
"喷射压力脉动" 英文翻译 : injection-pressure fluctuation
"喷嘴喷射压力" 英文翻译 : nozzle injection pressure
"燃料喷射压力" 英文翻译 : fuel injection pressure; fueling injection pressure
"燃油喷射压力" 英文翻译 : fuel-injection pressure
"太阳辐射压力" 英文翻译 : solar pressure
"精密注射压缩技术" 英文翻译 : precision injection compression technology
"朗之万辐射压力" 英文翻译 : langevin radiation pressure
"氧化剂喷射压力" 英文翻译 : oxidizer injection pressure

例句与用法

Influence of the injection pressure to plastic mould core offset
注射压力对塑料模具型芯偏移量的影响
Water pressure under 3 psi gently expand the folds of the colon wall to release entrapped fecal matter
大肠水疗法设备能够维持一个规范和安全注射压力,让水清洗,以达到末端结肠
Effects of injection pressure on the microstructures and mechanical properties of short glass fiber injection - moulded reinforced polypropylene
短玻纤增强聚丙烯注射压力对微观结构和力学性能影响
Screw bat type pre - plasticized installation , bigger capccity in piasticising , good quality in mixed refine , accuracy in measuring . minimum loss in injection pressure
螺杆式预塑装置，塑化能力大，混炼质量好，计量准确，注射压力损失小。
The influence of the injection pressure to the mold cavity thickness was analyzed , formulas of circular mold cavity thickness were calculated , providing theory basis for deciding the mold cavity dimension rightly
摘要分析了注射压力对模具型腔壁厚的影响，推导了圆形型腔壁厚的计算公式，为合理确定注射模具型腔壁厚提供了理论依据。
The green body of high quality could be obtained at injection molding temperature from 160c to 180 c , injection molding pressure from loompa to 120mpa , keeping pressure from 40mpa to sompa , mold - temperature 32c , cooled from 2 min to 4 min
注射温度为160 180 ，注射压力为100 120mpa 、保压压力为40 50mpa 、模具温度为32 、冷却时间为2 4min注射成型后，注射坯的质量较好。
Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time , injection time and injection pressure . though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position , we forecast the injection parts quality and the possibility injection flaw and its position , optimize the gate position . in this paper , though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding , we get the law of how the injection parameter influence the injection process
在相同的注射条件下，通过分析喂料在不同直径和长度流道中的流动规律，得到了喂料在流道中的速度场、压力场和温度场，找到了流道长径比的合理取值范围，并得出通过改变流道设计可实现对现有设备资源充分利用的结论；给出了不同注射压力下，型腔压力与充模时间关系曲线和喂料熔体平均充填速度与充模时间关系的曲线，得到了注射压力对充填时间和型腔压力的影响规律，确定了最佳的充模时间、注射时间和注射压力；通过分析采用不同位置浇口注射时注射件关键位置单元的流动速度和压力分布，预测了注射件的成形质量，或可能产生的注射缺陷及位置，优化了浇口设置。