油腔的英文

• oil recess, oil pocket
• oil reservoir(sump)
• sac

• "油"英文翻译    oil; fat; grease
• "腔"英文翻译    cavity; chamber
• "液压油腔" 英文翻译 :    fluid chamber
• "油腔滑调" 英文翻译 :    glib; unctuous; have a smooth, oily tongue; speak glibly; oily and fleshy; with one's tongue in one's cheek 他说起话来油腔滑调的。 he speaks glibly.; he has a glib tongue
• "油腔滑调的" 英文翻译 :    unctuous
• "花言巧语，油腔滑调" 英文翻译 :    i won’t be deceived by her banana oil
• "他说起话来油腔滑调的" 英文翻译 :    he has a glib tongue
• "油枪嘴" 英文翻译 :    grease gun nipple
• "油枪式粘度计" 英文翻译 :    grease gun viscometer
• "油桥" 英文翻译 :    aburahashi
• "油枪润滑" 英文翻译 :    grease-gun lubrication
• "油切换装置" 英文翻译 :    oil distributor device
• "油枪螺纹接头" 英文翻译 :    grease gun ni le; grease gun nipple; grease nipple
• "油侵" 英文翻译 :    inrush of oil; oc; oil cut
• "油枪接头" 英文翻译 :    grease gun fitting

• Check that there is no lubricating oil in the machine base , bearing and oil chamber
  检查机座，轴承和油腔无润滑油。
• The motion of plunger of oleo damper excited by colored gaussian noise with exponential correlation time is governed by first order nonlinear differential equation
  摘要油液阻尼器受指数型高斯色噪声外激励时，活塞在油腔内的运动可用一阶非线性动力学方程描述。
• However , many of those studies focused on the structures of bearing itself . and few studies have been done on the gas cavity caused by the decrease of oil - pressure in the oiling system , which influences bearing
  但是大多数研究都集中在轴承结构本身，对供油系统中由于供油压力变化而造成油腔中出现气穴现象对轴承特性影响的研究较少。
• The method of indirectly measuring force exerted on ground by bucket is used to check cantilever bucket - wheel stacker / reclaimer counter - weight , working out the hydraulic cylinder force to determine the force exerted on ground by bucket and thus counterweight value
  摘要针对悬臂斗轮堆取料机配重的校核提出了1种间接测定接地力的方法，即通过悬臂升降液压缸上下油腔压力计算出液压缸受力，进一步推算出堆取料机的接地力，从而确定配重安装量。
• In this way , when obturation cubage leave absorb oil cavity it connects the eduction oil cavity with the v trough and with the increasing of the turning angle , the size of the cross section of v trough become bigger and bigger , which make the pressure between the cavity of two blades much higher and higher , and until it completely connects the eduction oil cavity , it reaches the pressure of the eduction , and it can effectively reduces the fluid noise caused by high pressure return flow
  这样，当密闭容积离开吸油窗口之后，通过v型尖槽逐渐与排油窗口连通，随着转角的增加， v型尖槽通流截面积逐渐增大，这就使两叶片间容腔内的压力逐渐升高，直至完全接通排油窗口时，才升压达到压油腔的压力，这样可以有效地降低因高压回流而引起的流体噪声。

• 油腔什么意思：见“ 油腔滑调 ”。