比压的英文

发音:

"比压"怎么读用"比压"造句

英文翻译手机版

beta ratio
ecific pre ure
specific pressure
unit pressure

"比"英文翻译 2
"压"英文翻译 press; push down; hold down; ...
"比压器" 英文翻译 : potential transformer; pt
"比压头" 英文翻译 : specific head
"对比压" 英文翻译 : reduced pressure
"比压规范" 英文翻译 : specific pressure regime
"比压应力" 英文翻译 : specific compressive stress
"参比压力" 英文翻译 : reference pressure,
"打浆比压" 英文翻译 : specific beating prtessure
"对比压力" 英文翻译 : reduced pressure
"对比压强" 英文翻译 : reduced pressure
"接地比压" 英文翻译 : contact area pressure ratio; unit pressure of ground
"磨木比压" 英文翻译 : specific pressure of grinding; unit pressure of grinding
"拟对比压力" 英文翻译 : pseudoreduced pressure
"平均比压" 英文翻译 : mean specific pressure; means specific pressure
"切削比压" 英文翻译 : specific cutting pressure
"直流比压机" 英文翻译 : direct-current potential transf-ormer
"高比压仿星器" 英文翻译 : high-beta stellarator
"工作密封比压" 英文翻译 : operating unit sealing load
"假对比压缩性" 英文翻译 : pseudo-reduced compressibility
"预紧密封比压" 英文翻译 : pretightening unit sealing load
"比压器,计器用变压器" 英文翻译 : potential transformer
"界限预紧密封比压" 英文翻译 : limit pretightening sealing load
"开角接地比压器" 英文翻译 : open-delta ground potential transformer
"拟对比压缩系数" 英文翻译 : pseudoreduced compressibility

例句与用法

Broad - based projects use off - road tires , adhesion , grounding than the small , and their climbing ability
采用宽基工程越野轮胎，附着力大，接地比压小，爬坡能力强。
The basic structure and the seal principles of the hard packing were presented , and the formula of specific pressure was given
介绍了硬填料密封的基本结构及密封原理，给出了比压计算式。
The cross - section area of the internal sprue , the fill speed , the fill time and injection pressure are important die casting technology parameters
摘要内浇道截面积、充填速度、充填时间和压射比压都是重要的压铸工艺参数。
Tys120llgp bulldozer is rigid suspended , power shift , hydraulically controlled and track - type . it is applicable for the extra requirement of the ground pressure
Tys120超湿地推土机系刚性悬挂、机械和动力换档变速传动、液压操纵的结构型式，是一种能满足使用工况对接地比压有特殊要求的湿地型履带推土机。。
The chemical reaction control of cuo - al system has been studied . the results show that the chemical reaction is more stable when cupric oxide and aluminium is put respectively into molten copper
在此基础上，实验研究了cuo ? al体系的化学反应控制，得出了采用cuo和al分别加入法比压块加入法会使反应进行的更加平稳。
Tys165 bulldozer is of power shift , hydraulically controlled and track - type . it features good performance , flexible operation , good quality , high efficiency , especially used in waterlogged area
Tys165推土机系液力机械传动、液压操纵、低比压履带推土机。该机性能优良，操作灵活方便，质量可靠，工作效率高，特别适合沼泽地和含水量比较高的松软地带使用。
The cross section area of the internal sprue of the die casting dies designed should be of proper value , and matches perfectly the fill speed , the fill time and injection pressure in case that the die casting dies fail in the design
设计压铸模时应当确定恰当的内浇道截面积，并使之与充填速度、充填时间和压射比压保持较好的匹配，以防止压铸模设计的失败。
According to simulation results we decide the location of parting face and cooling system 、 the shape and location of runner and gating system etc . after that we take the az91d magnesium alloy shell of motorcycle engine as an example to proceed fine factors ( plunger injection speed 、 pouring
然后以az91d镁合金摩托车发动机外壳为例,进行五因素(压射速度、浇注温度、锻造时间、压射比压、锻造压力)四水平l16 ( 45 )正交实验,在普通压铸过程中关闭锻造功能。
Touch on developing large - flow and high - pressure ratio impressor and large - enthalpy drop turbine , reducing harmful emission , solving the major problems of high - temperature blade material , cooling , protective coating and single - grain blade casting , and comfirm some important manufacturing techniques
涉及了开发大流量高压比压气机、大焓降涡轮，降低有害排放量，解决高温叶片的材料、冷却、保护涂层及单晶叶片铸造等主要问题，并确认了一些关键的制造技术。
According to the moving characteristics of tracklayer , when the vehicle is on ramp and the ground ' s vertical pressure is linear , the calculating formulas of relationship between the deviation of the instantaneous steering center , the position of vehicle ' s gravity , steering radius , moving velocity , moving acceleration , and vehicle ' s orientation , were obtained by the theory and method of vector analysis in mathematics and mechanics
摘要根据履带式车辆的运动特点，运用数力学中矢量分析理论和方法，推导了接地比压为线性分布时履带式车辆在斜坡上转向时，瞬时转向中心偏移量与车辆重心位置、转向半径、行进速度、加速度、车辆方位相互关系的计算公式。