模线的英文

• loft line
• lofting
• mold line
• mould (or mold) line

• "模"英文翻译    mould; pattern; matrix
• "线"英文翻译    thread; string; wire
• "分模线" 英文翻译 :    die line; die parting line; flash line; flask line; paring line; partingline; separating line; silhouette; split line
• "合模线" 英文翻译 :    joint line; spew line; sprue line; spue line
• "模线,型线" 英文翻译 :    molded line
• "模线尺" 英文翻译 :    batten
• "模线缝" 英文翻译 :    match mark
• "模线台" 英文翻译 :    loft floor
• "外模线" 英文翻译 :    outer mold line
• "相模线" 英文翻译 :    sagami line
• "合模线，装配机" 英文翻译 :    assembly line
• "泥封(合模线)" 英文翻译 :    lute a mold
• "拼合线 分模线" 英文翻译 :    splitline
• "齐面分模线" 英文翻译 :    flush parting line
• "下分模线" 英文翻译 :    lower opening
• "折分模线" 英文翻译 :    broken parting line
• "放样；理论模线的绘制" 英文翻译 :    lofting
• "理论模线的绘制" 英文翻译 :    lofting
• "硬质合金拉丝模线抛光机" 英文翻译 :    carbide drawing die wire polishing machine
• "模限制" 英文翻译 :    mode confinement
• "模下压板" 英文翻译 :    die slide
• "模系" 英文翻译 :    mode group; model system; paradigm
• "模纹花坛" 英文翻译 :    carpet flower bed carpet bed
• "模箱" 英文翻译 :    casting box; mold box; mold jacket; molding flask; moulding box
• "模温机" 英文翻译 :    die heater

• Can we add ejector sleeves or ejector pins in the boss of this part
  产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？
• There ' s an undercut at this position and it needs a slider . it will also have a parting line on this side , is that ok
  产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？
• None of the figures required the slightest bit of trimming , with no flash and no extra plastic ( thanks to the separate parts policy )
  没有一个兵人需要即使是最轻微程度上的清理合模线，没有飞边也没有任何多余的东西（由于各部分分开开模的策略） 。
• Discussions with customers in details regarding contraction ratio , cavity number , gluing type , mold pulling out angle , and ripping , thus meeting product requirements
  1开模前与客户详细讨论各项细节，如收缩率、模穴数、胶口形式、拔模角度、拆模线- - -等等。以满足您对产品的需求。
• Standard of moulding is typical tamiya with very clean and crisp details with no flash and just the bare minimum of pin marks to be removed and the usual fine moulding seams which will require care on the smaller parts
  模型的标准是典型的“田式风格” ，带有清晰明快的细节，最大限度的减少了推出孔之类该去除的累赘，小零件上面的合模线要特别注意。
• Resurvey the column axis and elevation line , and mark out the column form line , 1 : 2 cement mortar will be used to leveling at the column bottom . “ 井 ” shape rack will be set around each column , and mark elevation control line on it
  将柱轴线、标高线复测投点，弹出柱支模线，将柱脚支模处用1 : 2水泥砂浆找平，每根柱周围搭设井字架，在井字架上抄测标高控制线。
• Based on a systematic discussion on the contents , characteristics and the up - to - now accomplishments of these three operations in cagd , we present our researches in three ways as follows : ( 1 ) efficient evaluation for parametric curves and surfaces based on generalized ball bases based on the generalization of mathematical model of surface lofting program in the consurf system , two generalized ball surfaces and the recursive algorithms for evaluating them are given . furthermore , the conversion algorithms from bezier form of a surface to these two generalized ball forms are presented
  在系统地论述cagd中此三类运算的内容、特点、已有研究成果的基础上，就以下三方面给出了研究成果： ( 1 )基于广义ball基的参数曲线曲面快速求值以前英国航空公司consurf系统机身模线程序数学模型的推广为基础，定义了两类广义ball基曲面，给出了求值的递推算法，推导了b zier曲面到这两类曲面的转换算法