板长的英文

• ban zhang
• length of panel

• "板"英文翻译    board; plank; plate
• "长"英文翻译    older; elder; senior
• "甲板长" 英文翻译 :    bosun
• "刮板长度" 英文翻译 :    squeegee length
• "护索板长枕" 英文翻译 :    bolster
• "甲板长椅" 英文翻译 :    deck bench
• "商船甲板长" 英文翻译 :    bosun
• "踏板长度" 英文翻译 :    tread length
• "自由板长度" 英文翻译 :    free slab length
• "凹板延板长板" 英文翻译 :    concave extension plate
• "板长厚比参数" 英文翻译 :    plate slenderness parameter
• "有效踏板长度" 英文翻译 :    effective pedal length
• "舱面长椅甲板长椅" 英文翻译 :    deck seat
• "黑色的黑板长又直" 英文翻译 :    black black
• "甲板长椅舱面长椅" 英文翻译 :    deck bench
• "板场" 英文翻译 :    itaba
• "板车" 英文翻译 :    plate trailer
• "板层状鱼鳞病" 英文翻译 :    ichthyosis lamellar; lamella ichthyosis; lamellar ichthyosis
• "板衬底倒装片" 英文翻译 :    flichion board
• "板层状小体" 英文翻译 :    lamellar body
• "板撑墙坝" 英文翻译 :    slab and buttress dam
• "板层状节理" 英文翻译 :    slab-layered joint
• "板程序框图, 操作程序框图" 英文翻译 :    flowsheet
• "板层状的" 英文翻译 :    lamellated

• In practice, the length l of the plate is limited by technical difficulties of manufacture .
  实际上，由于加工技术困难，板长L是有限制的。
• Longboards come second after shortboards in number of designs
  长板长板的设计花样之多仅次于短板。
• Board lengths and weights dropped dramatically towards the end of the sixties
  到60年代末，板长和板重迅速锐减。
• In practice , the length l of the plate is limited by technical difficulties of manufacture
  实际上，由于加工技术困难，板长l是有限制的。
• A new plate length calculation method based on spiral curve equation for spiral plate heat exchanger
  基于螺旋线方程的螺旋板换热器板长计算方法
• The function of combination cutting : it can reach 6 sets of cutting groups , each group can cut 10 types of glass length one by one
  花切功能：可实现六组编组功能，每组可对十种不同板长玻璃依次切割。
• Automatic correct the tolerance : if you input the actual value it can reach automatically correct the tolerance of length , opposite angle line , snapping position and glass plate falling position
  误差自动校正：对板长误差.对角线误差.掰断位置误差及落板下落位置误差，只要输入实际值，可实现一次性自动校正。
• The main results show that : ( 1 ) the mechanism of laser bending is very different from that in bending with hard tools . ( 2 ) the bending angle is varied along scanning direction , and there is a deformation wave in the process . ( 3 ) the effects of sheet length on bending can be neglected while the length is more than 10 times of thickness . ( 4 ) the sheet width has much higher influence on the bending process
  分析发现：激光弯曲成形时板料的应力状态与机械折弯时有根本不同；当激光束沿直线单向扫描时，板料两端的弯曲角度不同；板料的长度大于10倍板厚或5倍光斑尺寸时，板长对弯曲角度的影响不再显著；沿扫描方向，距离光斑中心3倍光斑尺寸以外的区域，仍然对弯曲变形量产生影响。