最大变形的英文

• maximum distortion

• "最大"英文翻译    maximum
• "变形"英文翻译    be out of shape; become defo ...
• "最大变形最大失真" 英文翻译 :    maximum distortion
• "大变形" 英文翻译 :    distortion, of welded vessels; large deformation
• "大变形虫" 英文翻译 :    chaos chaos
• "大变形理论" 英文翻译 :    large-deflection theory
• "都要用大变形" 英文翻译 :    set large
• "最大变幅距离" 英文翻译 :    the greatest range
• "用支撑防止大变形" 英文翻译 :    supports to prevent distortion
• "最大弯曲变形" 英文翻译 :    maximum flexibility
• "大变动" 英文翻译 :    cataclysm; catastrophe; earthquake; macrochange
• "大变革" 英文翻译 :    revolution
• "大变脸" 英文翻译 :    the great change
• "大变异" 英文翻译 :    antigenic shift
• "变大变满 缩小" 英文翻译 :    wax dwindle
• "大变动的" 英文翻译 :    cataclysmal; cataclysmic
• "大变异细胞" 英文翻译 :    ltc
• "放大变流器" 英文翻译 :    inverter amplifier
• "放大变压器" 英文翻译 :    amplifying transformer
• "极大变换" 英文翻译 :    maximal transformation
• "美丽大变身" 英文翻译 :    beauty channel
• "人格大变更" 英文翻译 :    capitisdeminutiomaxima
• "山河大变" 英文翻译 :    (bring about) a great change in the mountains and rivers
• "由大变小" 英文翻译 :    down
• "元音大变位" 英文翻译 :    great vowel shift

• Plastics piping and ducting systems . injection - moulded thermoplastics fittings for pressure piping systems . test method for maximum deformation by crushing
  塑料管道和导管系统.压力管道系统用注模热塑配件.用压碎法测定最大变形的试验方法
• Factors influencing its deformation are analyzed by the system , the statistic formula estimating maximum deformation and its place have been obtained
  利用该系统，对影响基坑变形的各因素进行了有限元数值模拟分析，得出了简明估算深基坑最大变形及其位置的统计关系式。
• Based on the numerical results , an optimum design model , which considers the maximal deformation of the piles as objective function , is put forward with the computer language apdl provided by ansys program
  在此基础上，利用ansys软件提供的apdl语言，提出了以桩体最大变形为目标函数的优化设计方法，对板桩间距进行了优化设计。
• Imitate to the launch environment , carry through 15g overloading acceleration analysis to the modal , get the maximum deform and stress of mirror tube structure on static force condition , validate the stiffness and the strength of the structure
  模拟发射环境,对模型进行了15g过载分析,得出了静力作用下结构中的最大变形和最大应力,验证了系统的刚度和强度。
• Results after oral administration of gukangning capsule , the mean trabecular plate density , the mean trabecular plate thickness and the trabecular bone volume , bmd and maximum strain of the rats , were significantly increased more than that of the osteoporotic model ( p < 0 . 05 )
  结果经骨康宁治疗后，骨质疏松大鼠的平均骨小梁数、平均骨小梁宽、骨皮质指数、股骨骨密度、股骨的最大变形能力等增加，并明显高于骨质疏松组( p < 0 . 05 ) 。
• Then some instances have been put out to certify that the maximum deformations calculated by the method are good enough to meet the need of the engineering . it has also been pointed out that this method has many advantages to direct f . e . m for it needs less parameters and the parameters are easy to be obtained
  最后指出这些公式相对于直接利用有限元程序计算有如下的优点：涉及参数少且易确定、实用性强，而且计算方法易掌握，但是并不能准确预测出墙体的整体变形性状与最大变形值的位置。
• This is to say , pu composite hollow fiber membranes pore size can become large with transmembrane pressure increasing , and can recover completely with transmembrane pressure reverting to original pressure at a specification condition . from the hagen - poiseuille equal ion , pu composite hollow fiber membrane pore radius magnification was calculated . in our experiment , the variation of membrane pore radius attained to much six times larger than the primitive membrane pore radius
  根据一般非变形膜的纯水通量一压力差的直线关系，首次提出了孔径变化分离膜的纯水通量一压力差的曲线关系，并根据hagenf公式，理论上计算出了几种pu复合中空纤维膜最大变形时的膜孔径为原始膜孔径的倍数，最小膜孔径变化也达到原始孔径的一倍多，最大膜孔径变化达到原始孔径的六倍多。
• Works on the bending roll system of four - roll rolling mill , the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys , the maximum deformation of the work roll was calculated , and the curve of the gap adopting the least - squares method was fitted , which set the base of the further calculation of load - gap shape
  摘要以四辊轧机的弯辊系统为研究对象，利用有限元分析软件ansys研究弯辊力和辊间接触应力引起工作辊形状的变化，计算工作辊弯曲的最大变形量，并用最小二乘法对辊缝曲线进行拟合，为进一步计算有载辊缝形状提供可靠的理论依据。
• Theoretical research on the type and mainframe tripled frequency converter : on the basis of building finite element models , dividing grid , application of load in the software of ansys , the dynamic and static performances are calculated , the value of the deformation , the first natural frequency and corresponding mode of the frequency converter are obtained , finally , the dynamic performances of the frequency converter are analyzed
  对型三倍频组件和主机三倍频组件的理论研究:采用通用ansys软件对组件进行合理建模,划分网格,施加载荷,在此基础上对它们进行了静态分析和动态分析,得到最大变形量、低阶固有频率和相应的振型,并对组件的动态性能进行了分析。