方位轴的英文

• azimuth axis
• azimuthal axis

• "方位"英文翻译    position; bearing; direction ...
• "轴"英文翻译    axle; shaft
• "方位轴线" 英文翻译 :    azimuth axis
• "定位轴" 英文翻译 :    fix shaft; locating shaft
• "零位轴" 英文翻译 :    null axis
• "水位轴" 英文翻译 :    axis of heights
• "方位" 英文翻译 :    position; bearing; direction; points of the compass; placement 测定船舶方位 fix the bearings of a ship; 目标方位 target bearing; 借助罗盘, 旅行者可以找到自己所处的方位。 with the aid of a compass the traveler can find his bearings. 只要记住这座小山位于正北方, 你就能确定你所在的方位了。 you can orient yourself by remembering that the hill is due north
• "不定位轴承" 英文翻译 :    nonlocaling bearing; non-locating bearing
• "定位轴承" 英文翻译 :    alignment bearing; locating bearing
• "定位轴环" 英文翻译 :    set collar
• "定位轴套" 英文翻译 :    ansatzbuchse
• "偏位轴线" 英文翻译 :    offset alignment
• "自位轴承" 英文翻译 :    pivoted bearing; self-aligning bearing; tilted pad bearing; tilting bearing
• "车床用定位轴" 英文翻译 :    the parts and units of jigs and fixtures―positioning shaft for lathe
• "直线对位轴承" 英文翻译 :    aligning bearing
• "自动调位轴承" 英文翻译 :    self-aligning bearing
• "自位轴承支座" 英文翻译 :    self aligning support; self-aligning support
• "不定位轴承，浮动轴承" 英文翻译 :    non-localing bearing
• "单位轴马力产冷量" 英文翻译 :    refrigerating effect per brake horse-power
• "浮动轴承,不定位轴承" 英文翻译 :    non-locating bearing
• "球面轴承,自位轴承" 英文翻译 :    self-aligning bearing
• "止推轴承,定位轴承" 英文翻译 :    locating bearing
• "自调位轴承支座" 英文翻译 :    self-aligning support
• "方位, 方位角" 英文翻译 :    azimuth
• "方位方位" 英文翻译 :    azimuth range

• This azimuth motion is known as the ballistic deflection error .
  这种绕方位轴的运动称为冲击偏差。
• The dial index will rotate in azimuth, giving an incorrect heading reading .
  读数示标会绕方位轴转动，给出不正确的航向读数。
• Searching satellite is to change the azimuth angle and pitching angle by making antenna circumrotate azimuth axis and pitching axis with controller , so antenna can point itself to different satellite according to the demands
  寻星就是通过控制器的控制使天线围绕方位轴和俯仰轴旋转，从而改变天线的方位角和俯仰角，使天线根据要求对准不同的卫星。
• The controller adopts tms320f240 dsp as its main control unit , using code wheel for angle measurement , using synchronous serial communications interface for the duplexing data communication between the controller and the upper computer , using rs - 232 interface for the communication between the pitch axis controller and the azimuth axis controller , and then developed the interface circuit to the motor driver
  根据控制器研制要求,提出总体方案。控制器采用dsp作为主控单元,利用光电码盘测角,利用同步串行通信接口与上位机进行双向数据通信,利用rs - 232接口进行俯仰轴和方位轴控制器之间的通信,并研制了与电机驱动器的接口电路。
• The design and simulation of the servo controller had been researched based on the optical track device for lunar rover made by dept . of astronautics engineering of hit . the main research are following : firstly , according to performance requirements , the control scheme is determined , and the control model are selected after analyzing the steady and dynamic characteristic . and the control equation are obtained
  首先根据系统的性能指标要求,在分析了系统的稳态和动态性能的基础上,确定了系统的控制方案,建立伺服控制系统各环节的数学模型,对视觉平台的控制方程进行了简化处理,消除了方位轴和俯仰轴之间的力矩耦合,得到了相互独立的方位轴和俯仰轴的控制方程。
• Research also leads to some directions for future in vestigation . in the dissertation the development actuality of correlative tracking technology around the zenith are summarized by the numbers . three solutions are presented , that is , tilt azimuth axis design , three - axis design , program steering
  本文以测星精密光电望远镜和地基激光反卫星跟踪望远镜项目为课题背景，在系统的总结国内外过天项目标跟踪技术发展现状的基础上，归纳出三种解决方案：方位轴倾斜方法、增设次俯仰轴方法、程序引导方法。
• That is , the occasional situation where the object of interest passes directly overhead ( 90 zenith pass ) . azimuth axis must rotate nearly 180 ? instantly . therefore , the standard two - axis altitude - azimuth pedestal will be unable to remain pointed at the object through the zenith pass event
  所谓天顶盲区问题是指目标过天顶时对地平式设备方位轴有一个极大的过载要求，需要方位轴瞬时调转180 (或略小于180 ) ，此时方位变化的角速度和角加速度在数学意义上是无穷大，导致目标丢失。