斜孔的英文

• angle hole
• angling hole
• angular hole
• crooked hole
• downward borehole
• inclination
• inclined hole
• slant hole
• splay

• "斜"英文翻译    oblique; slanting; skew; bev ...
• "孔"英文翻译    hole; opening; aperture
• "偏斜孔" 英文翻译 :    deflected borehole; deviating hole; drifted borehole
• "斜孔道" 英文翻译 :    flume
• "钻斜孔" 英文翻译 :    rat holing
• "偏斜孔岩心" 英文翻译 :    deflecting core
• "偏斜孔钻进" 英文翻译 :    deflected drilling
• "斜孔掏槽" 英文翻译 :    inclined hole cut; inclined-hole cut
• "斜孔下帮" 英文翻译 :    low wall of the hole
• "斜孔小窗" 英文翻译 :    hagioscope; squint brick
• "斜孔准直器" 英文翻译 :    slant hole collimator
• "斜孔钻法" 英文翻译 :    off-angle drilling
• "斜孔钻进" 英文翻译 :    slant drilling; slant hole drilling
• "钻斜孔法" 英文翻译 :    off angle drilling; off-angle drilling; off-drilling
• "双斜孔准直仪" 英文翻译 :    bilateral slant hole collimator
• "斜孔定向钻进" 英文翻译 :    inclined-directional drilling
• "斜孔三路旋塞" 英文翻译 :    three-way oblique bore stopcock
• "斜孔网状塔板" 英文翻译 :    kittel tray
• "斜孔造斜工具" 英文翻译 :    muleshoe orienting device
• "变角斜孔准直器" 英文翻译 :    variable-angle slant-hole collimator
• "旋转斜孔准直器" 英文翻译 :    rotating slant-hole collimator
• "钻偏斜孔用的钻头" 英文翻译 :    sidetracking bit
• "可变角度斜孔准直器" 英文翻译 :    variable-angle slant-hole collimator
• "旋转式斜孔体层摄影术" 英文翻译 :    rotating slant hole tomography
• "斜空" 英文翻译 :    slant hole
• "斜坑道" 英文翻译 :    sloping adit

• Laboratory glassware ; double oblique bore stopcocks
  实验室玻璃仪器.双斜孔旋塞
• Heat transfer characteristics of platelet transpiration - cooling thrust chamber
  多斜孔层板发散冷却流动传热特性
• The measured ratio of drainage using the said two ways is rather similar to that of numbers going through the discontinuities ( i . e . about 2 )
  仰斜孔排水效果明显优于铅直孔，二者实测排水量之比与其穿越结构面的数目之比十分一致( 2 ) 。
• A numerical study is reported to investigate the flow and temperature fields for jet array impingement cooling , inclined multi - hole film cooling and impingement / effusion film cooling
  运用数值计算的方法分别对阵列射流冲击冷却、多斜孔气膜冷却以及冲击-发散复合冷却方式的流动与传热特性进行了三维数值研究。
• It can not only manufacture die holders of various standards for customers , but also non - standard holders according to their drawings . the processing includes precise frames , water - carrying holes , angle holes , thimbles , front edges , and 3 - d forming dies
  不仅?客户制作各种标准模架，还可根据客户的来图要求，制作各种非标模架，加工范围包括精框精框，运水孔加工斜孔顶针止口及三维成型模具加工等。
• The experimental results are provided to show that : ( 1 ) edgetone generated by slanted hole configuration is main sound source , ( 2 ) screen and spllitter - plates successfully suppress the edgetone , ( 3 ) the design way in refer ence [ 1 ] for low noise wall is very useful
  实验结果表明： ( 1 )斜孔所产生的边缘音是最主要的声源； ( 2 )用加网和加隔片都是抑制边缘音的有效方法； ( 3 )文献[ 1 ]介绍的低噪声壁板的设计方法具有实用性。
• Firstly , for jet array impingement cooling , the effects of the distance of adjacent holes , the impinging distance and jet reynolds number on heat transfer characteristic at the target wall are summarized under staggered holes arrangement and the same hole diameter . and then , the numerical simulation of inclined multi - hole film cooling has been studied . the influence factors examined in this case include blowing ratio and the distance of adjacent holes
  首先通过对射流冲击冷却方式的研究,分析了相邻孔间距、冲击间距以及射流入口雷诺数对冲击靶面换热系数的影响情况,然后对多斜孔冷却方式进行了数值模拟,重点探讨了吹风比和相邻孔间距对绝热温比与壁面换热系数的影响规律,最后,针对冲击-发散复合冷却流场的计算物理模型,研究吹风比、相邻孔间距的变化对冲击-发散复合冷却流动与传热特性的影响。
• Results show that all the geometric parameters have remarkable effects on combustion performance ; the swirl of intake air generated by skew intake holes enhances fuel - air mixing , minimizes dead zone and stabilizes the flame with reverse flow , but the excessive reverse flow can cause overheat in combustion chamber and exhaust ; the consistency of flow resistance in intake and exhaust system is conducive to the stability of heater performance
  研究表明，燃烧室进气孔的孔径、孔数、孔的分布及方向等均对燃烧性能影响很大；斜孔所产生的旋转进气，虽具有强化燃气混合、消除死区和回流稳焰的作用，但回流过度会使燃烧室及排温过高；保证进排气系统流动阻力（压力）的一致性，有助于保证加热器性能稳定。