支撑梁的英文

• bearing beam
• brace summer
• support beam
• supporting beam

• "支撑"英文翻译    prop up; sustain; support
• "梁"英文翻译    beam
• "弹性支撑梁" 英文翻译 :    elastically-supported girder
• "简单支撑梁" 英文翻译 :    simply su orted beam; simply supported beam
• "两端支撑梁" 英文翻译 :    beam on two supports
• "支撑梁z" 英文翻译 :    brace summer
• "发动机支撑梁" 英文翻译 :    engine beam
• "撑梁" 英文翻译 :    bracing boom; breast beam
• "一端夹紧另端滚动支撑梁" 英文翻译 :    clamped-roller-supported beam
• "支撑刚性梁, 加劲[强]梁, 垛间支撑梁" 英文翻译 :    buttress brace
• "加撑梁" 英文翻译 :    propped beam
• "斜撑梁腹" 英文翻译 :    braced web
• "支撑" 英文翻译 :    1.(抵抗住压力) prop up; sustain; support 支撑危局 prop up a perilous situation; 坑道顶用柱子支撑着 。 the pillars sustain the roof of the pit.2.(勉强维持) support; prop up3.[建筑] strut; brace; 支撑板 [纺织] facing bar; tie strap; 支撑点 [军事] strong point; center of resistance
• "侧支撑" 英文翻译 :    side shore
• "撑杆；支撑" 英文翻译 :    brace
• "窗支撑" 英文翻译 :    window stay
• "钢支撑" 英文翻译 :    steel shotcrete
• "拱支撑" 英文翻译 :    arch brace
• "横支撑" 英文翻译 :    transverse strut
• "后支撑" 英文翻译 :    rear prop
• "坏支撑" 英文翻译 :    mechanical support
• "脚支撑" 英文翻译 :    foot support
• "角支撑" 英文翻译 :    angle stiffening
• "木支撑" 英文翻译 :    lignum shotcrete; timber strut; timbering set; timbering support; wood support; wooden brace
• "前支撑" 英文翻译 :    front prop

• The ntsb says the wing of that seaplane that crashed off miami had cracks in the main support beam that probably went unseen for a long time
  安全运输委员会说,在迈阿密坠毁的水上飞机的机翼在主要支撑梁处有断裂,这种情况已经很久都没有发生过了
• The ntsb says the wing of that seaplane that crashed off miami had cracks in the main support beam that probably went unseen for a long time
  安全运输委员会说,在迈阿密坠毁的水上飞机的机翼在主要支撑梁处有裂纹,这个裂纹可能已经很久了，但是一直没有检测到
• The accelerometer which has simple fabricated process and high sensitivity and small parasitic capacitance and residual stress is hybrid integrated with the interface circuit using ic nude chip . so the density of the package is increased , and the noise of the sensing system is decreased . these found the base of capacitive accelerometer module using the mcm method
  该传感器制作工艺简单，灵敏度高，支撑梁采用u型，减小了刻蚀后的残余应力，用玻璃作为衬底，减小了衬底和硅可动质量块间的寄生电容，且把传感器芯片和用ic裸片制作的接口电路集成在一起，提高了封装密度，减小了传感器系统的噪声，为采用mcm技术制作电容式加速度传感器模块打下了基础。
• At this time , the approximate mechanical model of devices has been put forward , which frequency is 70 mhz , then we analyzed the euler ? bernoulli equation , find that the frequency is determined by the resonator ’ s density thickness and length ; the free - free - beam 、 coupled beam 、 support beam 、 transducer have been designed ; the model was simulated and modal analyzed on the coventorware and were consistent with the designed parameter . the silicon surface microfabrication process was developed and emphatically introduced several key surface microfabrication technologies , and was simulated by coventorware
  本文通过分析欧拉-贝努立方程,得出滤波器的共振频率主要由谐振梁的密度、厚度和长度决定,考虑切变形和转动惯量的情况下,完成微机械谐振梁、支撑梁、驱动电容的设计;在coventorware软件上进行仿真,分析结果与理论设计比较好地吻合;对微机械滤波器的加工工艺进行设计,给出器件的完整的工艺流程,重点介绍微机械表面加工工艺,并在coventorware上进行仿真。