报废率的英文

发音:

"报废率"怎么读用"报废率"造句

英文翻译手机版

condemnation factor
condemnationfactor
condernmation facte
obsolescence factor
scrappage

"报废"英文翻译 announce invalidated check i ...
"率"英文翻译 rate; ratio; proportion
"报废率高设备" 英文翻译 : equipment with high obsolescence rate
"废品率报废率舍弃率" 英文翻译 : rejectionrate
"报废" 英文翻译 : announce invalidated check in paper; be declared worthless; discard as useless; dumping; scrap; report as unserviceable [useless]: 这架机器太旧, 快报废了。 this machine is so old that it will soon have to be scrapped.◇报废尺寸界线 condemning limit; 报废等值线 abandonment contour; abandonment; 报废巷道 [矿物学] abandoned workings; 报废件 discard; 报废零件 faulty part; scrapped parts
"实际陈废率" 英文翻译 : actual rate of obsolescence
"死亡残废率" 英文翻译 : rate of death and culling
"板报废" 英文翻译 : board scrapped
"报废；废料" 英文翻译 : scrap
"报废；废品" 英文翻译 : discard
"报废车" 英文翻译 : salvage
"报废船" 英文翻译 : condemned ship; condemnedship; disabled vessel
"报废的" 英文翻译 : abandoned; condemned; discarded; junked; obsolete; outofservice; scrapped; used-up
"报废法" 英文翻译 : retirement method
"报废件" 英文翻译 : discard
"报废孔" 英文翻译 : abandoned hole
"报废量" 英文翻译 : learies
"报废品" 英文翻译 : scraped products
"报废期" 英文翻译 : date of retirement; date or retirement
"固定资产退废率" 英文翻译 : out-of-service rate of fixed assets; rate of fixed assets retirement
"报废,勾销,注销" 英文翻译 : write off
"报废-易耗品" 英文翻译 : scrap expendable items
"报废板材" 英文翻译 : menders; scrapped planks; scrapped plates
"报废半成品" 英文翻译 : scrapping semi-finished goods
"报废表，寿年表" 英文翻译 : retirement table，mortality table

例句与用法

Assists in managing workers and production quality to minimized rejections
协助监督工人工作及生产质量，最大限度地降低报废率
Lead team to continue improvement current process , improve product quality , reduce scrap rate
带领团队不断提高现有的工艺流程，提高产品质量，降低报废率。
Monitor and control mass production products status and take actions to reduce the scrap rate and improve the process capability
控制/监控量产的品质状况，采取行动降低报废率，改善制程能力。
Installations for application and drying of paints and varnishes . application and combined booths . application by spraying . methods of measurement of rejects to atmosphere
涂料和清漆的应用及干燥设施.应用和组合间.受大气环境影响报废率的测量方法
At the initial stage of planar technique , b was employed as ideal diffusion impurity in base - region of npn si planar devices because of the match of its solid - solubility and diffusion coefficient in si with those of p in emission - region , and the good shield effect of sio2 film to b . but because of the relatively large solubility ( 5 1020 / cm3 at 1000 ) and the small diffusion coefficient , the linear slowly - changed distribution of acceptor b in pn junction can not be formed , which could not cater to the requirement of high - reversal - voltage devics . thereafter b - a1 paste - layer diffusion technology and close - tube ga - diffusion technology had been developed , while the former can lead to relatively large the base - region deviation and abruptly varied region in si , which caused severe decentralization of current amplification parameter , bad thermal stability and high tr ; the latter needed the relatively difficult pack technique , with poor repeatability , high rejection ratio , and poor diffusion quality and productio n efficiency
在平面工艺初期，由于b在硅中的固溶度、扩散系数与n型发射区的磷相匹配， sio _ 2对其又有良好的掩蔽作用，早被选为npn硅平面器件的理想基区扩散源，但b在硅中的固溶度大( 1000时达到5 10 ~ ( 20 ) ，扩散系数小， b在硅中的杂质分布不易形成pn结中杂质的线性缓变分布，导致器件不能满足高反压的要求，随之又出现了硼铝涂层扩散工艺和闭管扩镓工艺，前者会引起较大的基区偏差，杂质在硅内存在突变区域，导致放大系数分散严重，下降时间t _ f值较高，热稳定性差；后者需要难度较大的真空封管技术，工艺重复性差，报废率高，在扩散质量、生产效率诸方面均不能令人满意。
Among hundreds of the six sigma projects in schneider electric around the world , the project " reducing scrap ratio of c1 cells " from schneider beijing low voltage co . ltd . ( sblv ) in china , was recognized by the quality director , an important vip of schneider electric and the black belt & green belt from many countries
在施耐德全球近百个六西格玛项目中，来自中国施耐德北京低压电器有限公司（ sblv ）的项目"降低c1分断单元报废率”被施耐德电气质量总监、施耐德电气管理层及来自各个国家施耐德电气实体的黑带、绿带们所认可。