成型温度的英文

• forming temperature

• "成型"英文翻译    shaping; forming
• "温度"英文翻译    temperature
• "成型温度范围" 英文翻译 :    forming range
• "典型温度" 英文翻译 :    representative temperature
• "熔丝型温度" 英文翻译 :    fuse type temperature meter
• "相变型温度" 英文翻译 :    phase inversion temperature
• "型温度计" 英文翻译 :    angle thermometre
• "造型温度" 英文翻译 :    molding temperature
• "波登型温度计" 英文翻译 :    bourdontype temperature gauge
• "热熔型温度计" 英文翻译 :    fuse type temperature meter; fuse-type temperature meter; fuse-type thermometer
• "熔丝型温度计" 英文翻译 :    fuse-type temperature meter
• "旋入型温度计" 英文翻译 :    screw in type thermometer; screw-in type thermometer
• "圆盘型温度计" 英文翻译 :    dial type thermometer
• "窗装型温度调节器" 英文翻译 :    window type air conditioner
• "电子控制定型温度" 英文翻译 :    electronic setting temperature
• "干涉型温度传感器" 英文翻译 :    interferometric temperature sensor
• "平面型温度传感器" 英文翻译 :    planar temperature tra ducer; planar temperature transducer
• "熔丝型温度继电器" 英文翻译 :    fuse type temperature relay
• "熔丝型温度信号器" 英文翻译 :    fuse-type temperature meter
• "小型温度传感器" 英文翻译 :    mini-temperature se or; mini-temperature sensor
• "电导型温度变化率探测器" 英文翻译 :    electrical conductivity rate-of-change detector
• "带表盘型温度指示的电热干燥箱" 英文翻译 :    dial type electric drying oven
• "成型" 英文翻译 :    shaping; forming 爆炸成型 explosive forming; 冷滚成型 cold roll forming; 这箱子被压得不成型了。 the box was crushed out of shape
• "巨型温泉" 英文翻译 :    mammoth hot springs
• "中型温室" 英文翻译 :    medium-sized green house

• The optimal molding temperature and pressure of their composite are 140c and 7 . 3 mpa
  麻纤维复合材料的最佳成型温度为140 ，成型压力7 . 3mpa 。
• Both ramie and flax are hydrophilic fibers , their thermal stability is not pretty well
  麻纤维素含有大量羟基，亲水性强，热稳定性较差，加工成型温度不宜过高。
• The 4 factors , such as specific absorption of aggregate , dosage of fiber , dosage of cement and molding temperature , were assembled properly by orthogonal design method , the effects of the factors on the optimum proportion of asphalt were studied at the same time
  采用正交试验方法分析集料吸水率、纤维用量、水泥掺量及成型温度这4个因素对沥青混合料最佳油石比的影响程度。
• 4 . the optimistic resin system and the effect of resin content on the targets performance are discussed by orthogonal experiments , based on which , the moulding process parameters such as temperature , pressure , cycle and post - cure temperature are designed optimistically
  4 、通过正交试验确定了最佳树脂体系，确定了含胶量对靶板性能的影响，在选定基体材料基础上，通过正交试验分析，对复合材料成型工艺参数如：成型温度、成型压力、成型时间、后处理温度进行了优化设计，确定了体系的最佳成型工艺参数。
• The approaches of enhancing the mechanical properties of ramie and flax composites were studied in this paper . the effects of surface pretreatment , fiber content , molding temperature and pressure as well as the effect of electron beam , microwave and ultrasonic wave on the mechanical properties of the composites were explored . the experimental results show that : 1
  本文以苎麻、亚麻纤维为增强材料，线性低密度聚乙烯( lldpe )为基体，研制了两种麻纤维层压复合材料，研究了麻织物表面处理、纤维含量、成型温度、成型压力等对该复合材料力学性能的影响，得到了性能较为优异的麻纤维复合材料，探讨了复合材料的增强机理。