成型压力的英文

• briquetting pressure
• forming pressure

• "成型"英文翻译    shaping; forming
• "压力"英文翻译    pressure; tension
• "轮毂成型压力机" 英文翻译 :    hub punch press
• "粉末金属成型压力机" 英文翻译 :    powder metal moulding press
• "成型压板" 英文翻译 :    contoured squeeze board
• "成型压实" 英文翻译 :    contour squeeze
• "成型压头" 英文翻译 :    contoured squeeze board
• "成型压制机" 英文翻译 :    compacting press
• "注塑成型压机" 英文翻译 :    injection molding press; injection press
• "u型压力表" 英文翻译 :    u-gage; u-gauge
• "u型压力计" 英文翻译 :    u gauge; u-gauge
• "型压力计" 英文翻译 :    u-gauge
• "型压力接头" 英文翻译 :    flow cross t
• "造型压力" 英文翻译 :    molding pressure
• "钟型压力计" 英文翻译 :    bell pre ure gage; bell pressure gage; bell type manometer
• "重型压力机" 英文翻译 :    heavy duty press; heavy-duty press; super compactor
• "波登型压力计" 英文翻译 :    bourdontype pressure gauge
• "大型压力容器" 英文翻译 :    large pressurized vessel
• "底重型压力表" 英文翻译 :    deadweight gauge
• "型压力溶气罐" 英文翻译 :    rg type pressure dissolved air pot; tr type pressure dissolved gas pot
• "翼型压力分布" 英文翻译 :    airfoil pressure distribution; profile pressure distribution
• "翼型压力中心" 英文翻译 :    airfoil center of pressure
• "滑动成型压砖机" 英文翻译 :    sliding mold type press; sliding mould type press; sliding mould-type press
• "小型压力传感器" 英文翻译 :    miniature pressure cell
• "新型压力管反应堆" 英文翻译 :    advanced pressure tube reactor; aptr

• The optimal molding temperature and pressure of their composite are 140c and 7 . 3 mpa
  麻纤维复合材料的最佳成型温度为140 ，成型压力7 . 3mpa 。
• When compressing , the proper pressure is between 7 - 11 t / cm2 , the keeping time is 60s or so
  磁体压制时合适的成型压力在7 11t cm ~ 2之间，合适的保压时间在60s左右。
• It was found that the compression speed and compression stroke are the two factors affecting the molding pressure most significantly
  由模拟找出了压缩速度与压缩行程是两个影响成型压力极大的因素。
• It was found that the compression speed and compression stroke are the two factors affecting the molding pressure most significantly
  由仿真找出了压缩速度与压缩行程是两个影响成型压力极大的因素。
• In order to meet the need of production in practice , the proper molding water content , pressure and curing age were determined by experiment and analysis
  结合现场的生产要求，通过大量实验与分析，给出了合理的成型加水量、成型压力和养护龄期。
• The experiment results show that the reduction by carbon and nitridation is connected with the reaction temperature , molding pressure and ratio of tio2 / c of the sample
  实验结果表明：制备试样的成型压力、材料本身的tio _ 2 c比、氮化温度对氮化率有一定影响。
• As shown by the measurements , the electrical resistivity of sintered psc has a tendency of first decreasing and then increasing as the sintering temperature and / or sintering time increase . also it decreases with the increased pressure on the pressed powder compact
  对样品的电阻率进行了测量，总体呈现出随烧结时间和烧结温度的增加而先降低后增加的趋势，并随压坯的成型压力的增加而降低。
• The bonded magnets with excellent magnetic properties were manufactured by wetly - mixed epoxy and prfeb powders , which granularity was 100 to 140 , and under the pressure of 600 to 800 mpa . then the magnets were solidified 2 hours , under the temperature of 160c
  结果表明，当环氧树脂与磁粉采用溶剂湿混，成型压力选为600 ? 800mpa ，磁粉颗粒在100 ? 140目之间，磁体在160 ~ c真空固化2小时，粘结prfeb永磁合金的磁性能达到最佳。
• 3 . based on the gel time and dsc curve figure of two kinds of modified phenolic resin and flory and kissinger theory , the rage of cure process parameters for the resin system , moulding pressure and resin content are established
  3 、通过对二种改性酚醛树脂体系凝胶时间、 dsc曲线图的分析，引入flory理论、 kissinger理论，确定了树脂体系的固化工艺参数(固化温度、固化时间、后处理温度)范围；并初步确定了成型压力和树脂含量的范围。
• 4 . the optimistic resin system and the effect of resin content on the targets performance are discussed by orthogonal experiments , based on which , the moulding process parameters such as temperature , pressure , cycle and post - cure temperature are designed optimistically
  4 、通过正交试验确定了最佳树脂体系，确定了含胶量对靶板性能的影响，在选定基体材料基础上，通过正交试验分析，对复合材料成型工艺参数如：成型温度、成型压力、成型时间、后处理温度进行了优化设计，确定了体系的最佳成型工艺参数。