应力范围的英文

发音:

"应力范围"怎么读用"应力范围"造句

英文翻译手机版

range of stress
stre range
stress range

"应力"英文翻译 stress; strain; tension; cha ...
"范围"英文翻译 scope; limits; extent; bound ...
"安全应力范围" 英文翻译 : safe range of stress
"交变应力范围" 英文翻译 : range of alternating stre es; range of alternating stresses
"位移应力范围" 英文翻译 : displacement stress range
"许用应力范围" 英文翻译 : allowable stress range
"脉冲拉伸应力范围" 英文翻译 : range for pulsating tensile stresses
"脉冲压缩应力范围" 英文翻译 : range for pulsating compressive stresses
"应力范围减小系数" 英文翻译 : stress range reduction factur
"动力范围" 英文翻译 : dynamosphere
"轨道；势力范围" 英文翻译 : orbit
"核力范围" 英文翻译 : range of nuclear forces
"加力范围" 英文翻译 : reheat range
"拉力范围" 英文翻译 : weight range
"权力范围" 英文翻译 : power spectrum; scope of authority
"势力范围" 英文翻译 : a zone of influence; bossdom; perisphere; sphere of influence; turf; zone of influence
"视力范围" 英文翻译 : range of vision
"受力范围" 英文翻译 : field of load
"听力范围" 英文翻译 : earshot
"推力范围" 英文翻译 : range of thrust; thrust bracket; thrust range
"压力范围" 英文翻译 : pressure limits; pressure range; range of pressure
"引力范围" 英文翻译 : gravisphere; sphere of gravitational influence
"重力范围" 英文翻译 : sphere of gravity
"安全压力范围" 英文翻译 : pressure limit safety
"法官权力范围" 英文翻译 : extent of judge’s power

例句与用法

The highest stress range occurs near the support .
其最高应力范围发生在近支撑处。
The stress range histogram was used to estimate the effective root-mean-square stress range .
应力范围直方图可用作估算等效均方根应用力范围。
Range of alternating stresses
交变应力范围
Safe range of stress
安全应力范围
In the process of loading , the stress around the junction linearly increases at first and then the range of the high stress area enlarges
在逐步加载过程中，加载前期相贯区周边应力呈线性增长，一定程度后主要表现为高应力范围的扩大。
Tensile creep and rupture tests have been performed under vacuum for temperatures ranging from 1100 to 1500 and for stresses from 180mpa to 290mpa
基纤维体积分数约为40 。蠕变持久实验的应力范围为180mpa 290mpa ，温度范围为1100 1500 。
It seemed that the fiber and the matrix did not creep themselves in the range of the testing stress and temperature , so the matrix microcracking and interfacial sliding will be the main contributer to the macroscopic deformation of the three - dimensional c / sic composite
由于在所测定的温度区间和应力范围内，碳纤维和基体本身都不大可能发生蠕变。因此，基体开裂和界面的滑动是3d - c sic复合材料宏观变形的主要贡献者。
To prevent premature failure of the reinforced plastic fiberglass sucker rod , high quality products should be purchased , proper wells should be selected , the rod string design should be based on the stress range chart and operation and management should be carried out according to requirements
为防止玻璃钢抽油杆早期失效，应严把产品进货质量关；正确选择油井；按应力范围图进行玻璃钢杆柱设计；按要求作业施工；完善生产管理措施。
However , the die attach layer delaminated after 500 cycles and pcb cracked in the underfilled samples after long time cycling . c - sam is employed to investigate the delamination in the underfilled samples . highly concentrated stress - strain induced by the cte mismatch between the bga component and the pcb board , coarsened grain and two kinds of intermetallic compounds ( nisn / nisns ) which formed during reflow and thermal cycle and their impact on the reliability of solder joints are discussed in this paper
充胶样品粗化尤为严重； ? ni - sn金属间化合物包括两层：其中，靠近ni焊盘的那层比较平整，同时， eds结果分析表明其化学式近似为nisn ，而靠近焊料的那层呈板条状，化学式近似为nisn _ 3 ，文献表明其为亚稳相； ?充胶使得样品最大应力范围降了接近一个数量级并降低了dnp的作用，同时，器件失效模式变为芯片粘接层分层； ? c - sam结果表明本论文采用的充胶样品，芯片粘接层分层起始于500周左右，而经过2700周循环的样品，分层几乎扩展到整个界面。
To set up reasonable designing and manufacturing techniques and accurate calibration system and to speed up forming the native pvdf pressure sensors is the direction of this project . first , based on the piezoelectric theorem , the theoretic support of pvdf pressure sensors is deduced . according to purposes of practical projects , special purpose sensor configurations are designed and the corresponding calibration system based on shpb ( split hopkinson pressure bar ) technique is built in succession
本文从压电材料的一般压电控制方程开始，导出了pvdf压电薄膜测压技术的相关论据；根据测试目的以及被测结构的特点，设计了多种夹心式的传感器构造形式；摸索出了一套基于国产pvdf压电薄膜制作压力计的加工、安装工艺；建立了一套基于系统集成技术的多点pvdf压力测试的数据采集、处理系统；建立了一套基于shpb技术、适用于实际工程应力范围的pvdf压力计的动态标定方法，并对两种厚度的国产pvdf压电薄膜进行了标定。