工作行程的英文

• arbeitsgang
• forced stroke
• forward stroke
• impulse stroke
• operating stroke
• operational stroke
• power stoke
• power stroke
• woiking stroke
• working motion
• working stroke
• working travel

• "工作"英文翻译    work; operation; working; op ...
• "行程"英文翻译    route or distance of travel; ...
• "工作行程电机" 英文翻译 :    arbeitsgangmotor
• "工作行程速度" 英文翻译 :    speed of working stroke
• "踏板工作行程" 英文翻译 :    pedal working stroke
• "弹簧缓冲器工作行程" 英文翻译 :    working stroke of spring
• "油压缓冲器工作行程" 英文翻译 :    working stroke of oil butter
• "操作行程" 英文翻译 :    operational stroke
• "动作行程" 英文翻译 :    actuating length
• "操作行程测定" 英文翻译 :    operating distance measurement
• "工作行动" 英文翻译 :    job action
• "工作行为" 英文翻译 :    work behavior
• "分开的操作行程" 英文翻译 :    divided control runs
• "社会工作行政" 英文翻译 :    social work administration
• "作行" 英文翻译 :    sakuyuki
• "清粪工作行车线" 英文翻译 :    desludging route
• "单行程工作" 英文翻译 :    shot
• "工作台行程" 英文翻译 :    table stroke; table travel
• "工作者行程" 英文翻译 :    asp.net worker process asp.net
• "活动工作台行程" 英文翻译 :    travel of moving bolster
• "中国对外服务工作行业协会" 英文翻译 :    china association of foreign service trades
• "行程" 英文翻译 :    1.(路程) route or distance of travel; distance of run; length of travel; distance travelled; journey; flight 艰难的行程 hard journey; 漫长的行程 long route; 行程五千多公里 travel over 5,000 kilometres; 一小时的行程 an hour's march; 这将是一整天的行程。it will make a full day's march.2.[机械工程] stroke; throw; travel 活塞行程 piston travel; 滑枕行程 ram stroke3.[电学] range
• "操作行进图" 英文翻译 :    functional progression chart
• "合作行动" 英文翻译 :    cooperative action
• "做作行为" 英文翻译 :    apopathetic behavior

• Max of length of sliding and adjusting : 350mm
  最大工作行程: 350mm
• Let me get this straight . i change my schedule to meet you
  我跟你直说吧,为了见你我改了所有的工作行程
• Working stroke of sring buffer
  弹簧缓冲器工作行程
• Working stroke of oil buffer
  油压缓冲器工作行程
• 2 . the direct - contacting type limit switch has a working travel about 7 - 10mm
  2直碰式限位开关的工作行程约7 100mm 。
• Working travel mm
  工作行程mm
• Analysis and calculating to impacting stress and stroke of the impacting hammer in the striking of a pile hammer
  桩锤撞击过程中冲击应力及夯锤工作行程的分析与计算
• It can meet the requirements under the condition without loads . the working stroke is 6mm . and the stepping frequency is 300times / minute
  在空载的情况下，已基本能达到所要求的性能，其工作行程可达6mm ，步冲频率可达300次分。
• Considering that the smallest transmission angle could not reflect overall power transmission ability of whole mechanism , this paper indicates that finding the optimum power transmission efficiency while trying to make the mechanism compact is significantly important
  摘要针对机械的最小传动角不能反映机构的总体传力性能的缺点，提出只要找出机构工作行程中的最佳传力效率系数，并尽量使设计的机构紧凑，才具有重要的实用意义。
• In order to guarantee the request of accuracy of the work piece , all the series radial riveting machine are can add the tiny - scale device , the scale regulator are divided three kinds of specifications , they are 20mm , 30mm and 60mm . the different number representative different stroke of power head . each of scale representative the perpendicular distance 1 mm
  为保证铆接加工精度的要求，我公司可为客户提供加装刻度调节的服务，现将刻度盘的参数规格公布如下，标尺可分为20mm 30mm 60mm三种规格，分别对应不同工作行程的机型，每刻度代表1mm的垂直距离。

• 工作行程的法语：course active temps-moteur