导流管的英文

• honeycomb duct
• shroud
• thrust-augmenting nozzle

• "管"英文翻译    pipe; tube
• "导流管舵" 英文翻译 :    nozzle rudder; nozzle-rudder
• "回转导流管" 英文翻译 :    kort nozzle
• "级间导流管" 英文翻译 :    interstage crossover
• "加速导流管" 英文翻译 :    accelerating nozzle
• "减速导流管" 英文翻译 :    decelerating nozzle
• "圆形导流管" 英文翻译 :    circular housing
• "转动导流管" 英文翻译 :    movable control shroud
• "转向导流管" 英文翻译 :    steering nozzle
• "导流管螺旋浆" 英文翻译 :    nozzle propeller
• "柯特式导流管" 英文翻译 :    kort nozzle
• "科氏导流管舵" 英文翻译 :    kort nozzle rudder
• "螺旋桨导流管" 英文翻译 :    propeller nozzle; propeller shrouding
• "热空气导流管" 英文翻译 :    choke heater; hot air duct
• "外隔热导流管" 英文翻译 :    guide pipe with outer insulation
• "导流管厚度弦长比" 英文翻译 :    shroud thickness ratio
• "导流管式螺旋桨" 英文翻译 :    shrouded propeller
• "非轴对称导流管" 英文翻译 :    non-axisymmetric shroud
• "固定螺旋桨导流管" 英文翻译 :    fixed screw-propeller shrouding
• "轴不对称导流管" 英文翻译 :    non axisymmetrical nozzle
• "定螺距螺旋桨导流管" 英文翻译 :    fixed screw propeller shrouding
• "非同对称导流管螺旋桨" 英文翻译 :    non-axisymmetrical ducted propeller
• "装有导流管的螺旋浆" 英文翻译 :    ducted propeller
• "装有柯特式导流管的拖轮" 英文翻译 :    kort tug
• "导流" 英文翻译 :    conduction current; derivation; diversion kerb; river diversion; stream guidance; training for discharge

• Your baby isn't strong enough to suck, so we have to use intubation .
  你的宝宝还无法吞咽东西，所以我们使用导流管。
• Drainage catheters and accessory devices
  导流管和辅助设备
• 500kw rudder propeller harbour tug
  500kw导流管港作拖船
• Technical requirements for making and working of fishing vessel honeycomb duct
  渔船导流管拜制造及安装技术要求
• Hot air duct
  热空气导流管
• The conclusions are drawn as following : 1 . regularity of fabrication in aluminum matrix composite ring - shaped performs with large dimensions and effects of parameters were investigated , based on the novel crucible movable spray deposition technology and equipment . the optimal parameters are that the diameter of the delivery tube is 3 . 8mm , spray gas pressure is 0 . 8mpa , spray height is 200mm , and transferring pressure of sic is 0 . 5mpa
  通过系统的实验研究得到如下结论: 1 .基于新型的移动坩埚自动化控制喷射沉积环坯制备技术及装置,研究了大尺寸铝基复合材料环坯的制备规律,讨论了喷射沉积工艺参数对沉积坯形成过程的影响,得到了最佳工艺参数:导流管直径d = 3 . 8mm ,雾化气体压力p = 0 . 8mpa ,喷射高度h = 200mm , sic颗粒输送压力p送= 0 . 5mpa 。
• The optimal parameters of making high silicon content aluminum alloys is : spray height is 220 - 230mm , spray angle is 30 ? the scanning velocity of atomizer is 30mm / s , the original offset of the substrate is 30mm , rotation velocity of the substrate is 120rpm , spray gas pressure is l . ompa , the diameter of the delivery tube is 3 . 6mm , the drawing velocity of the substrate will be adjusted on - line with a plc on the basis of the spray
  通过对多层喷射沉积原理及工艺参数的研究，得出制备al - 22si - 3cu - 1mg合金的最佳工艺参数为：喷射高度为220mm - 230mm ，基底转速为120rpm ，雾化器扫描速度为30mm / s ，基底下降转速依据喷射情况由智能控制器进行实时调整，喷射角度为30 ，初始偏心距为30mm ，导流管直径为3 . 6mm ，雾化气压为1 . 0mpa 。
• In the part of detector , it mainly introduces the design of liquor tubes , heater , pressurize , and thermocouple ; in the part of controller , this design uses tms320lf2407 as the cpu . the design part mainly introduces controller circuit design which mainly contains data collection circuit , prepositive magnifying circuit , a / d convert circuit , failure self - diagnosis circuit , the tms320lf2407 interface circuit , temperature control circuit , display circuit , 4 ~ 20ma standard signal output circuit ; in the software part , it mainly introduces software chart of main program and partly linearization subprogram design
  检测器部分重点介绍了导流管的设计、加热器的设计、密封技术的设计以及测温电路的设计;控制器部分以tms320lf2407为核心,重点介绍了控制器电路设计,主要包括数据选择电路、前置放大电路、 a / d转换电路、故障自诊断电路、 tms320lf2407接口电路、控温电路、显示电路、 4 20ma标准信号输出电路共八个部分;软件设计重点介绍了主程序软件设计及分段线性化子程序设计。

• 导流管的日语：ヘリウズ管 ヘリウズかん