安放位置的英文

• riding position

• "安放"英文翻译    put away in safe place
• "位置"英文翻译    seat; place; location; site
• "重新考虑原油预热系统中预闪蒸滚筒安放位置" 英文翻译 :    rethink placement of preflash drum in crude preheat train network
• "堆放位置" 英文翻译 :    stowed location
• "开放位置" 英文翻译 :    clear position
• "全放位置" 英文翻译 :    full-out position
• "释放位置" 英文翻译 :    release position; releasing position
• "停放位置" 英文翻译 :    parking position; parking stand; stand
• "安放, 定位置, 位置" 英文翻译 :    emplacement
• "程序存放位置" 英文翻译 :    program location
• "襟翼全放位置" 英文翻译 :    full-flap position
• "飞机停放位置图" 英文翻译 :    aircraft parkingpiston
• "襟翼在全放位置的失速" 英文翻译 :    stall with full flaps
• "物料存放位置与布局" 英文翻译 :    location & layout of stores
• "安放" 英文翻译 :    lay; place; put in a certain place; ensconce 把仪器安放好。 put the instruments in their proper places. 烈士墓前安放着花圈。 wreaths were laid at the martyr's tomb
• "开放位" 英文翻译 :    open stance
• "安放的" 英文翻译 :    placed
• "安放在" 英文翻译 :    repose
• "安放者" 英文翻译 :    setter
• "安放,布置,划线" 英文翻译 :    layout
• "安放垫块" 英文翻译 :    setting cushion blocks
• "安放工程" 英文翻译 :    positioning
• "安放箭羽" 英文翻译 :    feather
• "安放龙骨" 英文翻译 :    keel laying
• "安放恰当" 英文翻译 :    wellset

• The placement of rear speakers greatly depends on the configuration of the room
  后扬声器的安放位置受房间配置的影响很大。
• The place to put the odf should be stable and reliable and far away from heat
  机房内光缆成端odf架安放位置要稳定可靠，远离热源。
• Hold centralizers or cement baskets on any position of casing , which ensures the positions of centralizers or cement basket to meet the design
  可将弹性套管扶正器或水泥伞置于套管本体上的任意部位，确保扶正器的安放位置满足设计要求。
• 2 . 3 . 6 residents are required to be familiar with the locations and operation methods of fire prevention facilities , and to take part in fire drills and demonstrations
  2 . 3 . 6宿生须知道各种防火设施的安放位置及使用方法，并参加防火演习。
• The riding position of signal wire was not always in the vertex of the impression from the conclusions of production , but in the position in which aluminous liquid tilted at last
  由生产实践总结出信号线的安放位置不一定在型腔最高点，而应在金属液最后充填的位置。
• Feeding , ingate design , air discharge , position of signal wire were analysed and discussed , aiming at the several questions in production of low pressure casting
  摘要根据低压铸造工艺的特点和生产实践，从补缩、内浇道设计、排气、信号线安放位置等方面进行了分析和探讨。
• Location of thrusters : be careful with how you place thrusters ? in particular , placing a hangar door close to a thruster , or a part of the hull of the ship a bit behind a thruster , is a big no - no
  推进器的定位：你在选择推进器的安放位置时要注意? ?讲究的来说，机库离得推进器过近，或者船体的某部分稍稍挡住推进器的喷口，这都是绝对不允许的。
• 10 examination of fire - protection apparatus are ( according to “ safe drawing ” ) checked the quality , amount , arrangement and lay position of portable type foam fire extinguisher , co2 fire extinguisher , every kind of fire extinguisher , fire hose boxes , fire axe , all kinds of fire fighting facilities and spare aeration equipment supply for firemen ' s breathing apparatus , and examine whether is easy to get and facility to use
  防火设备的检验（按照《安全图》 ）检验手提式泡沫灭火器、 co2灭火器、各类灭火器、消防水龙带箱、消防斧、各种救火设施和消防员呼吸器的备用充气设备的质量、数量、布置及其安放位置，以上设备是否能容易取得和方便使用。