复压的英文

• re-pressing

• "复"英文翻译    repeated; double; duplicate
• "压"英文翻译    press; push down; hold down; ...
• "复压级" 英文翻译 :    multi-pressure stage
• "复压片" 英文翻译 :    multiple compress tablet; multiple compressed tablet; multiplecompressedtablet
• "复压缩" 英文翻译 :    compound compression
• "反复压缩" 英文翻译 :    cyclic compression
• "复压涡轮机" 英文翻译 :    pressure compounded turbine
• "恢复压力" 英文翻译 :    recovered pressure
• "恢复压力法" 英文翻译 :    repressuring method
• "回复压力" 英文翻译 :    return pressure
• "可恢复压实" 英文翻译 :    recoverable compaction
• "往复压缩机" 英文翻译 :    reciprocating compressor
• "终恢复压力" 英文翻译 :    final buildupressure
• "重复压裂" 英文翻译 :    refracturing
• "重复压缩" 英文翻译 :    recompression
• "重复压条法" 英文翻译 :    compound layerage
• "往复压电效应" 英文翻译 :    reciprocating piezoelectric effect
• "型往复压缩机" 英文翻译 :    w-type reciprocating compre or w; w-type reciprocating compressor w
• "最终恢复压力" 英文翻译 :    fbp
• "冲压恢复压力比" 英文翻译 :    ram recovery pressure ratio
• "角式往复压缩机" 英文翻译 :    angle reciprocating compressor
• "双列往复压缩机" 英文翻译 :    duplex reciprocating compressor
• "往复压碎型破碎机" 英文翻译 :    reciprocating pressure type crusher
• "卧式往复压缩机" 英文翻译 :    horizontal opposed reciprocating compressor; horizontal reciprocating compre or; horizontal reciprocating compressor
• "校正后的恢复压力" 英文翻译 :    corrected buildup pressure; corrected buildupressure

• Pressure compounded turbine
  复压涡轮机
• The composite was pressed and sintered again to further enhance its synthetical properties . through this treatment , interface binding strength , compactness , conductivity and mechanical properties of the composite were prominently increased
  复压复烧处理后，铜基体与碳纤维之间结合状态良好，复合材料的致密度、电导率及机械性能均有显著提高。
• On this basis , we study the content of carbon nanotube influence to mechanical and electrical properties , we find composite materials can get high relative density after press ; at the volume content of carbon nanotube low 11 % , carbon nanotube may act as enhancement s to hardness , composite hold better electrical conductivity . after high 11 % , relative density quick decrease and resistance quick increase , for carbon nanotube do not complete disperse
  结果表明：在复压后复合材料可以达到比较致密的程度；在碳纳米管体积含量小于11时，碳纳米管可以提高复合材料硬度，且复合材料的电导率较高：碳纳米管体积含量大于11以后，因为碳纳米管发生团聚，导致相对密度下降、电阻率上升。
• Preparation for construction : the surface of the under layer should be even and firm , and in accordance with the design requirement , without loose material and flaccid site , and need to reroll 2 3 times within full - width range of the subgrade with vibrating roller before the construction , as well as test the compaction and defecting , to check whether there is unqualified point in the soil base
  施工准备：施工前下承层表面要平整、坚实，符合设计要求，无松散材料和软弱地点，施工前要用振动压路机在路基全宽范围内复压2 3遍，同时进行压实度及弯沉检验，检查土基中是否有不合格点。
• In this paper , systemic experiments are performed on the compositions , processes , microstructures and properties of some high quality pm inserts . main procedures such as mixing , compaction , sintering , re - compaction , re - sintering , heat - treatment , properties detection and mould design and so on are included in these experiments
  本文对几种高性能粉末冶金摇臂镶块的成分、工艺、组织和性能等进行了系统的实验研究，包括混粉、初压、初烧、复压、复烧、后续热处理、性能检测、现场模具设计等。