基准尺的英文

• reference meter

• "基准"英文翻译    datum standard; criterion; r ...
• "尺"英文翻译    chi,a unit of length
• "基价，基准尺度" 英文翻译 :    benchmark
• "基准尺寸" 英文翻译 :    basic dimension; basic size; characteristic dimension; reference dimension
• "基准尺度" 英文翻译 :    basic dimension; basic standard cost; characteristic dimension
• "大径基准尺寸" 英文翻译 :    basic major diameter
• "基准尺寸注法" 英文翻译 :    datum dimensioning
• "小径基准尺寸" 英文翻译 :    basic minor diameter
• "参考标准,基准尺度" 英文翻译 :    benchmark
• "准尺" 英文翻译 :    object staff (测量的)
• "标准尺" 英文翻译 :    gauge
• "规准尺" 英文翻译 :    gauge board
• "瞄准尺" 英文翻译 :    aiming arm; aiming rule
• "平准尺" 英文翻译 :    surveyor's rod
• "视准尺" 英文翻译 :    sight rule
• "水准尺" 英文翻译 :    leveling rod◇水准尺读数 staff reading
• "照准尺" 英文翻译 :    sight rule
• "基准" 英文翻译 :    1.[测量学] (测量时的起算标准) datum2.(泛指标准) standard; criterion; reference; basic standard◇基准点 reference point; datum point; 基准色 reference colours
• "标准尺，规格，测量" 英文翻译 :    gauge
• "标准尺寸" 英文翻译 :    gauge; normal dimension; normal size; standard dimension; standard measure; standard size; standard skeleton; standard-size; stock size
• "标准尺寸板" 英文翻译 :    stock sheets
• "标准尺寸的" 英文翻译 :    standard-sized
• "标准尺度" 英文翻译 :    normative scale; standard scale; standard size
• "测量的准尺" 英文翻译 :    object staff
• "非标准尺寸" 英文翻译 :    bastard size; nonstandard size; outsize

• On the basis of request to untouch measure online , this paper put forward the method of " datum dimension precision back " , and then the mathematics model is being established
  测试精度要求达到国家标准it6级。基于在线非接触测量的要求，本论文提出了基准尺精确后退的想法，并以此建立数学摸型。
• Analyze item by item the position of unintact cycle , the running clearance of unintact cycle , locking - deform , datum dimension regulating , repeatly install , power voltage wave and marking running etc . at the same time , we give the calculating formula to calculating the running marking random error , and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error , gyro - wheel diameter error , error caused by circumstance temperature , error caused by backing distance , angle error , delay error of data collecting circuit , lathe main shaft running error , workpiece install partial error
  对不完整圆的位置、不完整圆的转动间隙、锁紧变形、基准尺调整、重复安装、电源电压波动、标记转动等随机误差进行了逐项分析，并给出转动标记随机误差的计算公式。对大直径测量仪的系统误差?基准尺尺架误差、滚轮直径误差、环境温度引起的误差、后退距离引起的误差、角度误差、数据采集电路延时误差、车床主轴回转误差、工件安装偏心误差分别进行了计算，最后对误差进行合成。
• Especially , the idea of " datum dimension precision back " is being put forward , and this idea is being realized by backing composition composed by outer - diameter micrometer , airproof shafting , microwatch . at the same time , use " non - lock " to replace " lock " , this way make the system compact , eliminate many bigger error and resolve th
  尤其是提出了基准尺调整后精确后退的思想，并通过外径百分尺、密珠轴系、千分表组成后退机构加以实现。同时以“无锁”代“锁” ，使系统结构紧凑，受力小，消除了多项较大误差从而解决了测试精度低的关键问题。

• 基准尺的日语：ひょうじゅんしゃくど スタンダードスヶール