四辊轧机的英文

发音:

"四辊轧机"怎么读用"四辊轧机"造句

英文翻译手机版

four high mill
four high stand
four-high mill

"四"英文翻译 four
"辊"英文翻译 roller
"轧机"英文翻译 rolling mill
"可逆式四辊轧机" 英文翻译 : reversing four high mill; reversing four-high mill
"辊轧机" 英文翻译 : reduction roller mill; roller mill
"辊轧厂,辊轧机" 英文翻译 : rolling mill
"四辊粗轧机" 英文翻译 : four high rougher; four-high rougher
"四辊精轧机" 英文翻译 : four high finishing mill
"四辊式轧机" 英文翻译 : four high driven mill; four high mill; four high rolling mill; four roller mill; four-high rolling mill; four-roller mill; quarto mill
"肠衣辊轧机" 英文翻译 : casing stripper
"粗辊轧机" 英文翻译 : rough roller mill
"多辊轧机" 英文翻译 : cluster mill; multi-roll mill
"二辊轧机" 英文翻译 : duo mill
"二十辊轧机" 英文翻译 : twenty high roll mill; twenty high rolling mill; twenty-high roll mill
"分批辊轧机" 英文翻译 : batch roller
"混合辊轧机" 英文翻译 : mixing rolls
"角铁辊轧机" 英文翻译 : angle roller
"立辊轧机" 英文翻译 : edger mill; edging mill; edging stand; vertical miller
"六辊轧机" 英文翻译 : six high cluster mill; six roller mill; six-high-cluster mill; six-roller mill
"三辊轧机" 英文翻译 : edger; three-high mill; trio mill
"十二辊轧机" 英文翻译 : twelve high rolling mill
"双八辊轧机" 英文翻译 : double eight-high rolling mill; doubleeight-highrollingmill
"双二辊轧机" 英文翻译 : double duo-mill
"糖坯辊轧机" 英文翻译 : caramel brake
"五辊轧机" 英文翻译 : five roller mill; five-roller mill

例句与用法

Automatic rolling control system for four - high mill in citi
公司轧钢厂四辊轧机自动轧钢系统
Introduction of on - line operating condition monitoring system for medium heavy plate mill
四辊轧机工况在线监测系统浅析
Influence of electric grid voltage fluctuation on main motor drive system for four - high medium plate mill and its solution are introduced
摘要介绍了电网电压波动对中板四辊轧机主电机传动系统的影响和解决方法。
This paper establishes mathematical mode based two rolls mill and four rolls mill in aluminum product mill , and introduces the emulating with matlab
本文根据张家口铝制品厂的二辊轧机和四辊轧机中的apc控制系统建立模型，选择控制方案。
According to recording data of higher level monitor and control system when main motor drive system for four - high medium plate mill is operated , and relation between armature voltage of dc electromotor and ac input voltage of inverter , trip cause of dc fast automatic switch was analyzed in detail , and specific countermeasure and measures are given
根据中板四辊轧机主电机传动系统运行时的上级监控系统记录数据，以及直流电机电枢电压与变流器交流侧输人电压的关系，详尽地分析了直流快速自动开关跳闸故障原因，并提出具体的对策及措施。
Considering different microstructures and properties of metal of hardened layer and the core of back - up roller , the distributions of shear stress below surface and the contact stress between work roller and back - up roller of a four - high - mill were simulated with nonlinear fem
摘要考虑轧辊表面淬硬层与其心部金属材料组织性能的差别，采用非线性有限元方法对四辊轧机的工作辊与支撑辊间接触应力及辊内剪应力分布进行模拟，并将模拟结果与传统强度校核方法进行了对比分析，研究了轧辊淬硬层厚度对辊间接触应力的影响规律。
Works on the bending roll system of four - roll rolling mill , the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys , the maximum deformation of the work roll was calculated , and the curve of the gap adopting the least - squares method was fitted , which set the base of the further calculation of load - gap shape
摘要以四辊轧机的弯辊系统为研究对象，利用有限元分析软件ansys研究弯辊力和辊间接触应力引起工作辊形状的变化，计算工作辊弯曲的最大变形量，并用最小二乘法对辊缝曲线进行拟合，为进一步计算有载辊缝形状提供可靠的理论依据。