含胶量的英文

• gel content
• latex content

• "含"英文翻译    keep in the mouth
• "胶"英文翻译    glue; gum
• "量"英文翻译    measure capacity
• "含胶的" 英文翻译 :    gelation; gummiferous
• "含胶水" 英文翻译 :    stick water; tank water
• "残胶量" 英文翻译 :    residual sericin
• "敷胶量" 英文翻译 :    spread
• "容胶量" 英文翻译 :    charging capacity; magnitude of charge
• "填胶量" 英文翻译 :    compound input
• "涂胶量" 英文翻译 :    amount of spread; coat weight; coated weight; glue spread; glue-spread
• "脱胶量" 英文翻译 :    weight of boil-off gum content
• "含胶铝屑" 英文翻译 :    aluminum turning w/plastic
• "含胶乳的" 英文翻译 :    latex bearing; laticiferous
• "含胶生丝" 英文翻译 :    grey silk; gum silk; hard silk
• "含胶原料" 英文翻译 :    glue yielding material
• "内含胶纸带" 英文翻译 :    inclusion of gummed tape
• "单面涂胶量" 英文翻译 :    single spread
• "低胶量胶料" 英文翻译 :    low hydrocarbon stock
• "浸渍附胶量" 英文翻译 :    dip pickup
• "两而涂胶量" 英文翻译 :    double spread
• "含胶束的溶液" 英文翻译 :    micelle-containing solution
• "含胶水蒸发器" 英文翻译 :    stick evaporator; tank water evaporator
• "涂胶量控制辊" 英文翻译 :    doctor roll
• "含胶质重石油残渣" 英文翻译 :    heavy resinous petroleum residue
• "低胶量雨布胶料" 英文翻译 :    low rubber proofing mix

• Petroleum products - gum content of light and middle distillate fuels - jet evaporation method
  石油产品.轻馏分燃料和柴油燃料的含胶量.喷射蒸发法
• Petroleum products . gum content of light and middle distillate fuels . jet evaporation method
  石油产品.轻馏分和中间馏份燃料中的含胶量.喷射蒸发方法
• With the process of vigorous strides of reform and opening - up , the improvement of public cutural dynamics and physical stamina , cheap epdm colored granule , will enter many kinds of field of fine quality , have extremely good development and powerful potentiality
  可以根据客户的要求定制：颗粒的颜色大小含胶量可根据用户的要求定制，以适应用户的不同需求。
• 4 . the optimistic resin system and the effect of resin content on the targets performance are discussed by orthogonal experiments , based on which , the moulding process parameters such as temperature , pressure , cycle and post - cure temperature are designed optimistically
  4 、通过正交试验确定了最佳树脂体系，确定了含胶量对靶板性能的影响，在选定基体材料基础上，通过正交试验分析，对复合材料成型工艺参数如：成型温度、成型压力、成型时间、后处理温度进行了优化设计，确定了体系的最佳成型工艺参数。
• Making use of many layers composite technique and heat press technique to make artificial skull , through a series of performance testes ( including elongate performance , compress performance , curve performance , concussion performance , lay cut performance , concussion cut performance ) , making use of drainage method to calculate its average density , which is 1 . 25kg / m3 , and combustion method to calculate its content of macromolecule , which is 57 . 7 %
  利用多层复合技术和模压技术制备来的人工颅骨复合材料，通过对其一系列性能测试(包括拉伸性能、压缩性能、弯曲性能、冲击韧性、层间剪切强度和冲击剪切强度等) ，证明了该复合材料具有良好的物理机械性能。采用排水法计算复合材料的平均密度为1 . 25kg m ~ 3 ，采用灼烧法计算复合材料的含胶量为57 . 7 ，证明该复合材料比强度较高。
• Mainly made of super - fine three - dimensional staple fibers and mixed with some polyester staples of low melting point and finished products scarcely containing glue materials . after being calenderized and ironed , the product get smooth surface , silk - like glittering effect , light and exquisite hand feeling , softness , heat preservation , good washing endurance , no distortion and leaking . it feels like down but with fine tenacity and is the best among all spray bond padding products
  用超细三维中空短纤维为主要原料，配以部分低熔点涤纶短纤，成品含胶量极少，经过轧光烫平后，仿丝绵表面平整、有丝光、轻薄、手感细腻、柔软、保温好、耐水洗性极强、不易变形、不会跑毛、手感似羽绒，具有质地纤细、表面如蚕丝、有拉力、柔软等特点，是喷胶棉中最高挡的产品。
• Carbon fiber t300 was chosen as a co - hybrid fiber , and two different kinds uhmwpe fiber / t300 hybrid composites are prepared in both inner - laminar and inter - laminar styles . the inter - laminar hybrid composites exhibited better adhesion than the inner - laminar ones . for the optimized system dc88 / t300 / ve , the ilss reached 42 . 5mpa
  在混杂实验部分，研究了纤维状况(纤维种类、处理与未处理) 、混杂方式、含胶量等对混杂结果的影响；借助于sem以及建立的混杂模型对混杂机理进行了分析；对混杂复合材料进行了密度和耐湿热性测试。

• 含胶量的法语：teneur en gomme