可动部件的英文

• movable member
• moving parts

• "可"英文翻译    approve
• "动"英文翻译    harness cause disorder stir ...
• "部件"英文翻译    component; unit; parts; asse ...
• "运动部件；可动部分" 英文翻译 :    moving element
• "可动部分" 英文翻译 :    moving element
• "传动部件" 英文翻译 :    dirve components
• "从动部件" 英文翻译 :    driven part
• "浮动部件" 英文翻译 :    floating member
• "活动部件" 英文翻译 :    fahrgestell chassis
• "起动部件" 英文翻译 :    starting unit
• "启动部件" 英文翻译 :    start component
• "驱动部件" 英文翻译 :    drive element; drive part; driving parts
• "随动部件" 英文翻译 :    follow up unit; follow-up unit
• "运动部件" 英文翻译 :    moving component; moving member; moving parts
• "主动部件" 英文翻译 :    driving part
• "主驱动部件" 英文翻译 :    main-drive assembly
• "转动部件" 英文翻译 :    rotatable parts
• "输纸驱动部件" 英文翻译 :    tractor feed drive unit
• "速率随动部件" 英文翻译 :    rate follow up unit; rate follow-up unit
• "往复运动部件" 英文翻译 :    reciprocating part; reciprocation parts
• "位移随动部件" 英文翻译 :    displacement follow up unit
• "真实运动部件" 英文翻译 :    trackmaster
• "自动部件清单" 英文翻译 :    apl automated parts list
• "鼻中隔可动部分" 英文翻译 :    nasal septum mobile portion
• "无定向的可动部分" 英文翻译 :    astatic element

• In order to reduce friction , the moving parts of a machine are often oiled
  为了减少摩擦，机器的可动部件常常涂上润滑油。
• We have to oil the moving parts of the machine , the friction of which may be greatly reduced
  译：我们必须给机器的可动部件加油,以便使摩擦大大减少。
• Office furniture - tables and desks and storage furniture - test methods for the determination of strength and durability of moving parts
  办公家具.桌子和储存用家具.可动部件的强度和耐用性的测定用试验方法
• Because vortex flowmeter has no movable mechanical parts , the output signal of it is a frequency signal that is proportional to flow signal , and it has less pressure loss , wider measurement range , it is used widely
  由于涡街流量计具有无机械可动部件，可得到与流量成正比的频率输出信号，压力损失较小和量程比较宽等优点，因而应用相当广泛。
• The design has the characteristics of high accuracy , low cost and wide measuring range , and thus offers a reference for further developing practical multiphase flowmeters of non - radioactivity pollution , low press loss and non - moving components
  该方案具有可靠、成本低、测量范围广的优点，为研制无放射性、无可动部件、低压降的实用性多相流量计提供了借鉴。
• The gap element method is proposed in the paper for two kinds of problems , which include contact problem and gap joint problem . elasticity contact problem falls into the category of unknown boundary value problems . it follows that the contact area and contact conditions or states ( st
  文中给出了间隙元法在空间可动部件接触问题中的应用，推导了其几何边界条件和力学边界条件，利用虚功原理推导了含间隙元弹性接触问题的有限元方程式，给出了其数值解法的迭代步骤，并指出了利用间隙单元进行分析的特点。
• The main computer is programmed under windows , while the assistant computer is programmed under dos . the last , based on the idea of module - structure , the software of the testing system are designed , thus this software system is compatible and transplantable to design again . the experiment of measuring principle is taken : take the xy flat of lathe as the parallel - pole device and adjust the angle of sensor , the rotating - probe can test the felloe mould in scanning way
  借助虚拟仪器的思想，对测控系统进行了设计：采用光栅尺、光电编码器测量可动部件的运动量，分辨率高、误差小；采用细分驱动的步进电机装置，控制性能好；系统实施环境温度的检测、补偿，提高了检测精度；基于两级微机组建测控系统：主机为人机界面，采用windows编程，从机用dos编程，实时性好；软件设计采用兼容性和移植性好的模块式结构，便于二次开发。
• With a view to the contactor counterforce , which was calculated by the combination of spring - force and mechanical construction before , had the problem of mechanical matching . the contactor counterforce " one - off " measurement , which is realized by the synchronization testing of the placement based on opto - mechanism and the spring counterforce for the moving component , is put forward the fist time
  针对现阶段接触器反力特性主要采用弹簧力与机械结构组合的计算方法，存在机械配合性问题，将接触器光机电位移检测与可动部件弹簧反力特性检测同步进行，首次实现了接触器反力一位移特性的“一次性”测量。
• The measurement of oil / water two - phase flow is primarily accomplished by the combination of total flow rate and holdup measurement , and at present , the rotator flowmeter is used to measure the total flow rate . since the rotator flowmeter has movable parts , which makes its responsibility behave nonlinearly under poor environment of me under hole whose fluids have very complex and changeful characteristics and affects the measurement precision . what ' s more , the widely used centralized measurement instrumentation meets problems in oil wells characterized with high production or high water cuts
  通常油水两相流测量主要是通过总流量和持率的测量组合来完成的，目前在总流量的测量中主要使用的是涡轮流量计，由于涡轮流量计具有可动部件使其在流体特性复杂多变的恶劣井条件下的响应呈非线性变化规律，影响测量精度，此外，普遍采用的集流型测试仪器在高产井及含水率高的油井中使用也遇到困难，为此，一种新型的适合非集流型点测的测试方法和测试仪器亟待发展和推广。

• 可动部件的日语：かどうぶざい