受压元件的英文

• pressure element

• "受"英文翻译    receive; accept
• "压"英文翻译    press; push down; hold down; ...
• "元件"英文翻译    element; component; part; ce ...
• "非受压元件" 英文翻译 :    for nonpressure parts
• "标准受压元件" 英文翻译 :    standard pressure, parts
• "非受压元件的连接" 英文翻译 :    nonpressure parts attachment of; nonpressure parts, attachment of
• "锅壳锅炉受压元件强度计算" 英文翻译 :    strength calculation of pressure parts for shell boilers
• "锅炉受压元件焊接接头坏性能试验方法" 英文翻译 :    boiler pressure parts―mechanical test for welded joints
• "水管锅炉受压元件强度计算" 英文翻译 :    strength calculation of pressure parts for watertube boilers
• "船用辅锅炉及受压容器受压元件焊接技术条件" 英文翻译 :    welding specifications for pressure parts of marine auxiliary boiler and pressure vessel
• "测压元件" 英文翻译 :    load cell; pressure element
• "感压元件" 英文翻译 :    sensing element
• "加压元件" 英文翻译 :    pressure imposing element
• "水压元件" 英文翻译 :    hydraulic pressure cell
• "液压元件" 英文翻译 :    hydraulic components; hydraulic elements; hydraulic power tools; hydraulic pressure component; hydrauliccomponents
• "锅炉受压元件焊接接头金相和断口检验方法" 英文翻译 :    boiler pressure parts―metallographic examination and fracture test of weld joints
• "液压元件试验" 英文翻译 :    hydraulic element test
• "甲板坏液压元件" 英文翻译 :    hydraulic efficiency elements of deck machinery
• "液压元件课程设计" 英文翻译 :    course exerciese in hydraulic elements; course exercise in hydraulic elements
• "液压元件设计库" 英文翻译 :    thcd
• "中高压液压元件" 英文翻译 :    middle or high pre ure hydraulic element; middle or high pressure hydraulic element
• "测力传感器 测力盒 测压元件" 英文翻译 :    loadcell
• "液压元件通用技术条件" 英文翻译 :    hydraulic fluid power-general rules of technical requirements for hydraulic components
• "受压" 英文翻译 :    in compression
• "元件" 英文翻译 :    [电工] element; component; part; cell; organ 传输元件 transfer element; 电光元件 electrooptic cell; 电路元件 circuit component; 敏感元件 sensor

• Strength calculation of pressure parts for shell boilers
  锅壳锅炉受压元件强度计算
• Strength calculation of pressure parts for watertube boilers
  水管锅炉受压元件强度计算
• Technical specification of shop fabrication for pressure parts of chemical furnace
  化学工业炉受压元件制造技术条件
• Manufacturing specification for main pressure parts of marine auxiliary boilers
  船用辅锅炉主要受压元件制造技术条件
• Specification of strength calculation on pressure parts for chemical process furnace
  化学工业炉受压元件强度计算规定
• Welding specifications for pressure parts of marine auxiliary boiler and pressure vessel
  船用辅锅炉及受压容器受压元件焊接技术条件
• However , for attaching nonpressure parts to pressure parts , the filler metal chemistry shall match the nominal chemistry of the pressure part
  但将非受压元件焊接受压元件时所用的填充金属，应与受压元件的标称化学组成相配。
• 8 dissimilar metal welds ( ferritic to ausenitic - p1 to p8 ) are not permitted on pressure parts in hydrogen services or in wet sour services , as defined by secco
  受压元件在赛科公司所规定的氢或湿的酸性环境下工作时，不允许在不同金属间施焊（铁素体与奥氏体p1 p8 ） 。
• The calculation method of the utmost load of gray cast iron beam with rectangle section is obtained through the analysis of limit load behavior of the beam under the united action of bending and pulling , therefore the design method of limit load about forcing parts of cast iron pressure vessels is determined
  通过分析灰口铸铁矩形截面梁在纯弯曲和拉弯组合作用下极限载荷行为，提出灰口铸铁矩形截面梁极限载荷的计算方法，由此确定灰口铸铁压力容器受压元件的极限设计方法。