反推法的英文

• back-calculation

• "反"英文翻译    reverse side
• "推"英文翻译    push; shove
• "法"英文翻译    law
• "反推法标准率" 英文翻译 :    inverse standardized rate; isr
• "反推法标准化率" 英文翻译 :    inverse standardized rate
• "反推" 英文翻译 :    jet braking
• "推法" 英文翻译 :    pushing maneuver; pushing manipulation; pushingmanipulation
• "反推的" 英文翻译 :    regressive
• "反推进" 英文翻译 :    retropropulsion
• "反推力" 英文翻译 :    backward thrust; counter thrust; jet thrust; negative thrust; reaction thrust; reactive thrust; rearward thrust; reverse thrust
• "全反推" 英文翻译 :    full reversal
• "侧推法" 英文翻译 :    side pushing
• "顶推法" 英文翻译 :    incremental launching method; successive launching method
• "分推法" 英文翻译 :    parting pushing; parting-pushing manipulation
• "合推法" 英文翻译 :    meeting-pushing manipulation
• "类推法" 英文翻译 :    analogical method; method of analogy
• "内推法" 英文翻译 :    interpolation
• "逆推法" 英文翻译 :    backward pass; retroduction
• "平推法" 英文翻译 :    flat pushing; flat-pushing anipulation
• "牵推法" 英文翻译 :    pull-push technique
• "外推法" 英文翻译 :    extrapolated method; extrapolation method; extrapolation technique; method of extrapolation; trend projection
• "掌推法" 英文翻译 :    palm pushing
• "正推法" 英文翻译 :    forward pass
• "打开反推" 英文翻译 :    go into reverse
• "反推公式" 英文翻译 :    inversion formula

• The analytical results demonstrate that the lqr based design and dominant poles based design methods are effective
  分析和对比结果表明：基于lqr的反推法和基于主导基点的设计方法都是有效的。
• Abstract : in this paper , the generalized variational principle of ela stic and plastic problem with finite displacement is derived by means of semi - in verse method
  文摘:利用半反推法，导出了弹塑性有限变形率形式的广义变分原理
• It is given that quantitative diagnosis to estimation errors of internal temperature of a hot wire embedded at the center of a cylinder - shaped heat equipment
  摘要对采用红外监测反推法，由加热圆柱外壁温度，确定圆柱体内壁温度的误差进行了量化分析。
• Through these studies , preliminary results and understandings have been gained as follows : 1 ) propose a reverse - appraisal method that is more reliable based on imaging well log data to classify the lava flow orientations of volcanic rock facies , integrating with lava - debris thickness ratio
  通过研究，初步获得的成果和认识如下： 1提出了依据成像测井资料，划分火山岩岩相的熔岩流向反推法，结合火山熔岩与碎屑岩厚度比法，划分结果更可靠。
• Abstract : the effect of powder feed height on the thickness and density of powder rolled strip was calculated by using " deduction from ends of strip ” . the critical feed height ensuring uniform thickness and density of strip has been obtained . the effect of apparent density on the critical feed height is given as well
  文摘:本文通过“带材尾端反推法”计算出粉末轧制工艺中粉末堆料高度对粉末轧制带材厚度、密度的影响，并得出保证带材厚度、密度均匀的临界堆料高度；同时指出了松装密度对临界堆料高度的影响。
• Of reliability index ( monte carlo method and optimize method ) . compute the reliability index based on practical engineering example and mock example and show the process of reliability analysis . the method to design the parameter of composite foundation based on reliability analysis was given in the paper . draw the relation map of reliability index and mean - value of random variables , considering the difference influence degree about different random variables to reliability of composite foundation . the sensitivity coefficient that can reflect the influence degree about random variables to reliability was given and set up the theory frame for design of composite foundation based on reliability
  同时提出了基于可靠度分析的复合地基参数设计反推法，并且考虑了不同随机变量对复合地基可靠性的影响不同，做出可靠指标与随机变量均值关系图，提出了能够反映随机变量对可靠指标影响程度的敏感指标，为可复合地基靠性设计建立了理论框架。