压边力的英文

发音:

"压边力"怎么读用"压边力"造句

英文翻译手机版

black holder force
pressure-pad-force

"压"英文翻译 press; push down; hold down; ...
"边"英文翻译 side; section
"压边" 英文翻译 : holddown; side pressing
"高压边" 英文翻译 : hot side
"内压边" 英文翻译 : inner gasket
"受压边" 英文翻译 : compression flange; side under compression
"压边机" 英文翻译 : fianging press
"压边浇" 英文翻译 : lap gate
"压边圈" 英文翻译 : blank holder; clamping ring
"压边条" 英文翻译 : fillet
"软边力车轮胎" 英文翻译 : beaded edge cycle tire; beaded edge cycle tyre
"玻璃压边框" 英文翻译 : glass check
"开压边浇口" 英文翻译 : kissing
"拉深压边筋" 英文翻译 : draw bead
"冒口压边" 英文翻译 : riser pressure
"耐压边界" 英文翻译 : pressure resistance boundary
"压边点焊" 英文翻译 : mash spot welding
"压边滚焊" 英文翻译 : mash-welded joint
"压边滑块" 英文翻译 : blankholder slide
"压边机，卷边机" 英文翻译 : beading machine
"压边浇口" 英文翻译 : connor runner; corner gate; cornopgate; edge gating; kiss; lap gate; touch gate
"压边浇铸" 英文翻译 : lipcasting
"压边铆钉" 英文翻译 : open-end rivet
"压边针迹" 英文翻译 : machine stitch
"压边整缘" 英文翻译 : press trimming

例句与用法

This narrow range of blank - holder force is difficult to determine
合适的压边力范围是很难决定的。
Development of fuzzy expert control technique for aluminum electrolysis
基于模糊神经网络的压边力优化控制专家系统
Uniform blank holder force and local holder force ( non - uniform ) were tried
对压边力的分布采用了均匀压边力和局部改变压边力。
Elastic rubber method and rigid blank holders were used to apply blank holder force with different methods
对压边力的控制采用了弹性橡胶控制和刚性直接控制法。
At the same time , acquiring the formula of the minimum blank holder force that to be sure that the blank holder will not be lifted
同时，又得到了保证拉深零件时压边圈不被?起的最小压边力公式。
For wrinkles occurring in the central area of a stamped part with a complex shape , a workable range of blank - holder force does not even exist
因为起皱在冲压零件的中心位置以一个复杂的形状形成，甚至不存在一个合适的压边力范围。
The work reported here , adaptive numerical simulation was developed to adjust the magnitude of bhf continuously during the simulation process
摘要拉裂和起皱是板材拉深过程中的主要失效方式，研究表明，合理的压边力能有效降低拉深失效的可能性。
Hence , the blank - holder force must lie within a narrow range , above that necessary to suppress wrinkles on the one hand , and below that which produces fracture on the other
因此，压边力必须控制在一定的范围内，一方面增抑制起皱，另一方面防止破裂。
Taking typical drawing workpiece circular cup as the research object , a stamping technological parameters artificial neural network ( ann ) model for bhf forecast has been built up
摘要压边力是板料成形中的一个重要的工艺参数，也是板料拉深成形中的重要控制手段。
The predominant failure mode in stamping of sheet metal parts are wrinkling and fracture , in general , these defects may be eliminated by appropriate manipulated the blank holder forces
摘要起皱和断裂是板料成形过程的主要失效模式，合理控制成形过程中压边力，可以消除这些缺陷，提高成形性能。