单向扫描的英文

• simple scanning
• simplex scan
• single sweep scan

• "单向"英文翻译    one-way; unidirectional; sim ...
• "扫描"英文翻译    scan; scanning; scansion; sw ...
• "单向扫描技术" 英文翻译 :    single phase scanning technique
• "单向扫描器件" 英文翻译 :    telepantoscope
• "与摄象管类似的单向扫描器件" 英文翻译 :    telepantoscope
• "侧向扫描" 英文翻译 :    side scanning
• "侧向扫描器" 英文翻译 :    side scanner
• "垂向扫描器" 英文翻译 :    orthoscanner
• "定向扫描" 英文翻译 :    directed scan; directional scanning
• "反向扫描" 英文翻译 :    reverse scan; reverse sweep; scan backwards
• "反向扫描法" 英文翻译 :    backward scan technique
• "横向扫描" 英文翻译 :    transverse scan
• "横向扫描法" 英文翻译 :    transverse scanning method
• "径向扫描" 英文翻译 :    radial scanning; radial sweep
• "旁向扫描仪" 英文翻译 :    side scanner
• "前向扫描器" 英文翻译 :    forward looking scanner
• "双向扫描" 英文翻译 :    bilateral scanning
• "双向扫描术" 英文翻译 :    two-dimensional scanning technique
• "下向扫描" 英文翻译 :    down sweep
• "向扫描点" 英文翻译 :    scanning spot dimension
• "正向扫描" 英文翻译 :    scan forwards
• "轴向扫描" 英文翻译 :    axial scan
• "纵向扫描" 英文翻译 :    longitudinal scan
• "侧向扫描设备" 英文翻译 :    side-scan equipment; sidescan
• "侧向扫描声纳" 英文翻译 :    side scan sonar

• The main results show that : ( 1 ) the mechanism of laser bending is very different from that in bending with hard tools . ( 2 ) the bending angle is varied along scanning direction , and there is a deformation wave in the process . ( 3 ) the effects of sheet length on bending can be neglected while the length is more than 10 times of thickness . ( 4 ) the sheet width has much higher influence on the bending process
  分析发现：激光弯曲成形时板料的应力状态与机械折弯时有根本不同；当激光束沿直线单向扫描时，板料两端的弯曲角度不同；板料的长度大于10倍板厚或5倍光斑尺寸时，板长对弯曲角度的影响不再显著；沿扫描方向，距离光斑中心3倍光斑尺寸以外的区域，仍然对弯曲变形量产生影响。
• The simulation results suggest that , at the end of the scanning line , the dissymmetric temperature field and the great temperature gradient result in the balling phenomenon and great thermal stress , which could lead to the destruction of the sintering samples in this region . because of the coupling effect between scanning lines , the balling phenomenon is increased as the increase of the scanning lines , thus the over short scanning lines should be avoided in the sintering process . different scanning strategies have significant influence on the sintering
  模拟结果表明,扫描端点温度场的不对称及较大的温度梯度造成了端点球化现象,并在端点处产生较大的热应力,使烧结成形试样易在此处破坏;激光扫描线间的耦合作用使端点球化现象随扫描线的增加而逐渐显著,烧结时应避免过短的扫描线;不同扫描策略对烧结成形有很大影响,交替扫描会影响烧结试样的质量,实际制造时应采用单向扫描策略。