前轮定位的英文

• front alignment
• front wheel alignment
• wheel alignment

• "前轮"英文翻译    front wheel nosewheel
• "定位"英文翻译    fixed position; location; or ...
• "前轮定位仪" 英文翻译 :    front wheel angle tester; wheel alignment tester
• "前轮定位工具" 英文翻译 :    front wheel aligner
• "前轮定位，前轮校准" 英文翻译 :    front wheel alignment
• "前轮定位试验器" 英文翻译 :    front-wheel angle tester
• "携带式前轮定位仪" 英文翻译 :    portable alignment gauge
• "定位器，校直器，调整器；前轮定位仪" 英文翻译 :    aligner
• "前轮定" 英文翻译 :    front wheel hojack daniel
• "车轮定位" 英文翻译 :    wheel alignment
• "车轮定位仪" 英文翻译 :    wheel alignment meter
• "齿轮定位环" 英文翻译 :    gear collar
• "齿轮定位器" 英文翻译 :    pinion stop
• "四轮定位" 英文翻译 :    fmc
• "跳轮定位杆" 英文翻译 :    jumping wheel jumper
• "转向轮定位" 英文翻译 :    steering wheel alignment
• "换向轮定位板" 英文翻译 :    reversing wheel maintaining plate
• "四轮定位系统" 英文翻译 :    kds
• "指示轮定位杆" 英文翻译 :    indicator wheel jumper
• "转向轮定位仪" 英文翻译 :    wheel aligner
• "车轮定位仪试验台" 英文翻译 :    achs-lenkung-pruefstand
• "打点星轮定位杆" 英文翻译 :    strike star jumper
• "光束水准车轮定位" 英文翻译 :    light beam level wheel gauge
• "胶轮定位试验器" 英文翻译 :    front wheel angle tester
• "零偏距转向轮定位" 英文翻译 :    center point steering

• Later , the relationship between front wheel alignment parameters and tire wear is analysed by studying the tire model
  然后从轮胎模型入手分析前轮定位参数同轮胎磨损的关系。
• It also use adams _ car to build the kinematics model of front suspension , studying the varying rule of front wheel orientation parameter
  应用adamscar模块建立了前悬架运动学模型，探讨了前轮定位参数的变化规律。
• It use adams to simulate the front suspension kinematics and gain the rule of suspension frame affecting the front wheel orientation parameter
  对前悬架进行了运动学仿真分析，得到了悬架结构对前轮定位参数的影响规律。
• The method of independent suspension design is studied in detail and the relation among suspension movement , front wheel alignment parameters and tyre wear is analysed in this paper
  本文主要研究轻型汽车前独立悬架的设计分析方法以及轮胎磨损与悬架运动、前轮定位参数的关系。
• Then the math model of the relationship between the front wheel aligning parameters and tyre wear is obtained by taking the side slip angle of tyre as medium parameter , and the computer simulation is made
  并以轮胎侧偏角为中间变量，建立了前轮定位参数同轮胎磨损之间关系的数学模型，进行了计算机仿真计算。
• In the process of building model , the method of using experiments to collaborate with computer to acquire parameters was used . the front wheel orientation parameter , the absorber damp speciality and the quality of parts were all acquired by actual measure . the spring rigidity etc are acquired by calculation
  本文在模型建立过程中，采用试验与计算相结合的办法获取各种参数，前轮定位参数、减振器阻尼特性、零部件的质量均通过实际测量获得，弹簧刚度等通过计算获得。
• The kinematic performance of the macpherson suspension on a real vehicle is studied , and the changes of the front wheel alignment and the motion of the front wheel in the longitudinal and the transversal directions are figured . based on the requirements of general layout , a constrained optimization design model is set up with the steering cross rod ball joint position as the optimization variables ( design parameters ) , and the sum of steering cross rod length interference while the left front wheel turning and bouncing as the objective function . and the optimization results are worked out by programming on computer
  针对一种实际车型上的麦弗逊式悬架，计算分析了转向轮跳动时前轮定位角和车轮横向、纵向滑移量的变化情况，并根据实际车型上麦弗逊式悬架的空间布置要求，建立了以转向横拉杆断开点空间位置坐标为优化变量，转向横拉杆断开点空间布置坐标可变化范围为约束条件，车轮转向和跳动时转向横拉杆长度干涉量为目标函数的约束优化设计模型。