冲击式机组的英文

• impulse unit

• "冲击"英文翻译    lash; pound
• "式"英文翻译    type; style
• "机组"英文翻译    set; assembling unit; machin ...
• "冲击式" 英文翻译 :    impulse type
• "串级式机组" 英文翻译 :    cascade set
• "单室式机组" 英文翻译 :    single chamber unit; single-chamber unit
• "可逆式机组" 英文翻译 :    reversible machinery group
• "凝汽式机组" 英文翻译 :    condensing set
• "斜轴式机组" 英文翻译 :    slant unit
• "冲击式扳手" 英文翻译 :    impact wrench; striking wrench
• "冲击式泵" 英文翻译 :    impulse pump
• "冲击式操纵" 英文翻译 :    impulse maneuver
• "冲击式夯具" 英文翻译 :    impact compactor
• "冲击式加压" 英文翻译 :    impact pressing
• "冲击式铆接" 英文翻译 :    percussion riveting
• "冲击式磨机" 英文翻译 :    impact grinding mill
• "冲击式钎子" 英文翻译 :    jumper boring bar; percussion jumper; thrust borer
• "冲击式切割" 英文翻译 :    impact cutting
• "冲击式水轮" 英文翻译 :    impact wheel; impulse water wheel; impulse wheel
• "冲击式通机" 英文翻译 :    impulsion fan
• "冲击式涡轮" 英文翻译 :    impact wheel
• "冲击式铣刀" 英文翻译 :    impact mill
• "冲击式铣鞋" 英文翻译 :    impact mill
• "冲击式叶片" 英文翻译 :    impulse blades
• "冲击式仪器" 英文翻译 :    ballistic instrument

• An ultimate specific speed method checked by formula of manufacturer is proposed
  提出用极限比速法，并采用厂家公式校核的方法选取冲击式机组。
• The impulse type turbines made by ganfa , are ranging form 80 to 1 , 000m in water head , 200kw to 20mw in capacity and 0 . 55 to 2 . 3m in runner diameter
  我公司生产的冲击式机组适应水头801000m ，转轮直径0 . 552 . 3m ，容量20040000kw ，根据安装方式分为立式卧式两种，有单喷嘴双喷嘴和多喷嘴。
• The optimized model , in which water turbine is decomposed and placed along the spiral case ( placed at the nozzles for pelton turbine ) , is proposed in this paper . transient calculation for two projects showed that the proposed optimized model are reasonable and effective
  本文从理论分析入手，根据轴流式机组和冲击式机组的特点，提出把水轮机分解成多个水轮机，并把它们放置在蜗壳沿线(喷嘴处?对于冲击式机组)的优化方案，以减少用现有模型计算带来的偏差。
• The calculation model of hydro - mechanical transient in existence was deeply studied and the conclusion is that , for kaplan turbine and pelton turbine , neglecting differences of dynamic mater pressure along the turbine spiral case during transient may cause some error in the calculation of pressure rise and speed rise
  本文深入研究分析了轴流式和冲击式机组过渡过程计算的现有模型，指出现有模型中对蜗壳(进水管)部分的处理方法会给这两种机组的过渡过程计算带来相对较大的偏差。