主机程序的英文

• host program
• mainframe program

• "主机"英文翻译    main engine; master; host ma ...
• "程序"英文翻译    procedure
• "登机程序" 英文翻译 :    check-in procedure
• "调机程序" 英文翻译 :    tracingprogramme
• "计算机程序" 英文翻译 :    ccomputer program; computer program/computer; computer programming; computer programs; computerprogram; network analysis for system application
• "假脱机程序" 英文翻译 :    spooling program
• "联机程序" 英文翻译 :    in line procedure; in-line procedures; inline procedure; on line program; on-line program; on-line routine
• "人机程序包" 英文翻译 :    man-machine package
• "人机程序图" 英文翻译 :    man-machine process chart
• "随机程序" 英文翻译 :    random process; randomizer; stochastic process
• "随机程序库" 英文翻译 :    random library
• "停机程序" 英文翻译 :    pause program
• "脱机程序" 英文翻译 :    off line program; off-line programming; offline program
• "带-打印机程序" 英文翻译 :    tape-to-printer program
• "计算机程序包" 英文翻译 :    computer package
• "计算机程序段" 英文翻译 :    segment
• "计算机程序法" 英文翻译 :    computer algorithm
• "计算机程序库" 英文翻译 :    cpl computer program library
• "计算机程序学" 英文翻译 :    science of computer programming
• "计算机程序员" 英文翻译 :    computer programmer
• "开机关机程序" 英文翻译 :    start-stop procedure
• "联机程序编辑" 英文翻译 :    on-line program editing
• "联机程序调试" 英文翻译 :    on-line program debugging
• "联机程序调整" 英文翻译 :    debugging on-line
• "联机程序构造" 英文翻译 :    on-line program construction

• The last part of this paper describes the implement of engineering in hardware , software and host program
  第三部分从软、硬件和主机程序给出具体工程实现。
• The last part of this paper describes the implement of engineering in hardware , firmware and host program
  第三部分从硬件、固件和主机程序三个部分给出了具体的工程实现。
• Chapter five briefly introduces the implementation of system software including dsp , fpga and pc control programming
  第五章介绍了系统的软件实现，包括了dsp程序， fpga程序和主机程序。
• When all the measurements operation have completed , the host will send a series of commands to get the calculated results
  以上测量数据传送给主机，主机程序就可方便地计算出本设备的介损值。
• Chapter five briefly introduce the implementation of system software including dsp , fpga , device driver and pc control programming
  第五章介绍了系统的软件实现，包括了dsp程序， fpga程序、驱动程序和主机程序。
• The host programs or loaders can then use this connection to transfer the bootloader onto the target , where it is written to flash
  然后，主机程序或装入程序可以使用这个连接将引导装载程序传送到目标上，并将它写入闪存。
• On the order of a few bytes - that will initialize some dram settings and enable a serial or usb or ethernet port on the target to communicate with host programs
  根据几个字节的指令它将初始化一些dram设置并启用目标上的一个串行（或者usb ，或者以太网）端口与主机程序通信。
• Subsequently , several precepts are compared , including comparing some popular embedded operation systems , and the difference between $ clinux and standard linux is expounded . and then , the features of the operation systems and processors are compared , and clinux and mcf5307 become the target operation system and the processor . and then hardware design detail is given , including introduction about the primary chips and some key technique in the hardware design
  在第二章对各种方案进行了比较，比如比较流行的嵌入式操作系统的性能特点，并且比较了一下clinux与标准linux之间的区别，最后确定了clinux和mcf5307为目标操作系统和处理器；第三章详细介绍了本系统的硬件实施细节，包括对系统中使用到的主要芯片的介绍和系统硬件设计上的一些关键技术；第四章介绍了系统的软件实现，包括了bsp程序、主机程序、 clinux下驱动程序和用户应用程序。