临界冷却速率的英文

• critical cooling rate

• "临界"英文翻译    critical; crisis; criticalit ...
• "冷却速率"英文翻译    rate of cooling
• "上部临界冷却速率" 英文翻译 :    upper critical cooling rate
• "临界冷却速度" 英文翻译 :    critical cooling rate; critical cooling velocity; critical rate of cooling
• "上部临界冷却速度" 英文翻译 :    upper critical cooling rate
• "上临界冷却速度" 英文翻译 :    upper critical cooling velocity
• "下临界冷却速度" 英文翻译 :    lower critical cooling rate
• "马氏体临界冷却速度" 英文翻译 :    critical cooling rate
• "珠光体临界冷却速度" 英文翻译 :    pearlite critical cooling rate
• "特质淬火油(临界冷却速度快的)" 英文翻译 :    superquench oil
• "冷却速率" 英文翻译 :    cool-down rate; cooling rate; cooling speed; rate of cooling
• "冷却速率曲线" 英文翻译 :    cooling rate curve; cooling-rate curves
• "丝条冷却速率" 英文翻译 :    threadline cooling rate
• "中等冷却速率" 英文翻译 :    intermediate cooling rate
• "反相冷却速率曲线" 英文翻译 :    inverse cooling-rate curve
• "冷却速率倒数曲线" 英文翻译 :    inverse cooling curve
• "正冷却速率曲线" 英文翻译 :    direct rate curve
• "临界冷点" 英文翻译 :    critical cold point
• "冷却速度" 英文翻译 :    cool-down rate; cooling rate; cooling speed; cooling velocity; rate of cooling; speed of cooling
• "临界冷凝温度" 英文翻译 :    cricondentherm; critical condensation temperature; critical-condensation temperature; true condensing point
• "临界冷凝压力" 英文翻译 :    cricondenbar; critical condensation pressure
• "表面冷却速度" 英文翻译 :    surface cooling rate
• "瞬时冷却速度" 英文翻译 :    instantaneous cooling rate; momentary cooling rate
• "冷却速度试验器" 英文翻译 :    quenchometer
• "超临界速率" 英文翻译 :    speed; supercritical

• Based on these experiments , it may be claimed that there is segregation of sn to grain boundaries in 0 . 15 % c steel during cooling from a high solution treatment temperature . this segregation reduces grain boundary cohesion , which results in low hot ductility and intergranular fracture
  通过试验和计算得出: sn在0 . 1swt . % c钢中发生非平衡晶界偏聚的临界时间为1245左右，临界冷却速率大约为8 / s ，与试验结果基本一致。
• This segregation behavior of sn accords with the mechanism of non - equilibrium segregation . it can be obtained through the theoretical calculations that the critical time of sn non - equilibrium segregation is 124 seconds at 750 and the critical cooling rate is 8 / s when cooling from 1320 . it is suggested that controlling the cooling rate during continuous casting to avoid the critical cooling rate ( 8 / s ) and avoiding high stress near the trough temperature ( 750 ) may control the form
  通过研究残留元素sn的偏聚机制及其对o . 15wt . % c钢热塑性的影响，对试验钢进行脆性预测:建议在该钢的连铸过程中弯道矫直温度尽量避开塑性谷底温度750 ，二冷区的冷速尽量避开临界冷却速率8 / s ，从而可以减少该低碳钢连铸坯表面裂纹和横向裂纹，提高其成材率。